Want a regional phone & address? Pick your area.
Hotpoint·Washermedium severity
Hotpoint Washer Error Code tE
Wash-water temperature out of range
Common Causes
- 1Tub thermistor drifted or open
- 2Chafed sensor lead to the board
- 3Hot tap shut so only cold reaches the valve
Step-by-Step Troubleshooting
- 1
First confirm the hot hose is actually live — a closed hot tap alone will trip this on a fill
- 2
Find the NTC bead clipped to the outer tub and read it near ten thousand ohms at room temperature
- 3
Run the sensor lead back to the board and check for a rubbed-through spot or a loose plug
- 4
A reading that sits open or crashes to near zero condemns the bead — fit a new one
Pro Diagnostic Tip
This fault often has nothing to do with the sensor — a Hotpoint plumbed with only its cold hose live reads every fill as wrong-temperature. Prove the hot supply is open and warm at the valve before you ever unclip the thermistor.
You Might Also Notice
- •A cold wash even with a hot cycle picked
- •Wash temperature that never holds steady
- •Cycles dragging out longer than normal
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$175
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WH12X26093 NTC temperature sensorWH19X27243 wiring harness
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code tE disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Hotpoint error code tE mean?
Hotpoint error code tE indicates: Wash-water temperature out of range. This is a medium-severity issue affecting your washer.
How do I fix Hotpoint error code tE?
First confirm the hot hose is actually live — a closed hot tap alone will trip this on a fill Then, Find the NTC bead clipped to the outer tub and read it near ten thousand ohms at room temperature Then, Run the sensor lead back to the board and check for a rubbed-through spot or a loose plug There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error tE?
Besides the error code on the display, common signs include: A cold wash even with a hot cycle picked; Wash temperature that never holds steady; Cycles dragging out longer than normal. If you notice any of these symptoms, check your washer's display panel for error code tE.
How much does it cost to fix Hotpoint tE?
Repair costs for Hotpoint tE typically range from $75 to $175 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online