The short answer
A KEG draught cabinet is not an ice machine, and ice inside one is a symptom rather than a product: it usually means the box is set colder than it needs to be, or humid air is condensing and freezing on a cold surface. Ice on a line or a fitting is worth attention, because a frozen line will not pour. Where these usually stand, the room is the variable that moves most, so start there rather than inside the unit.
What you observe
- No ice is appearing, and there is no icemaker fitted — Many cabinets of this size make ice only in a tray you fill.
- Frost is building where you do not want it — Humid air reaching a cold surface, which is a door story before a cooling one.
- NEAR MISS — nothing in the cabinet is cold — That is a cooling failure, and it belongs on that page rather than this one.
Causes, most likely first on a KEG refrigerator
- The cabinet makes ice in a tray, not automatically — Id: nomaker — Most cabinets of this size and class have no icemaker at all. Ice comes from a tray and its speed is set by the compartment temperature. It ranks first here because it is both the commonest finding on this kind of unit and the cheapest one to rule out.
- Frost building where it should not — Id: frostbuild — Second: humid air entering past a tired seal or an ajar door freezes on the coldest surface it meets. That is frost growing, not ice being produced.
- Room heat and load — Id: ambient — Third: a warm room, a cabinet in the sun, or a door opened often all slow freezing to the point where the owner reads it as a fault. It moves up a place here because of where these units actually live: a warm room is a permanent load rather than an occasional one.
- Setting or mode, not a failure — Id: thermostat — Fourth, and less common: a dial that is an arbitrary scale rather than a temperature, or a mode set for storage rather than freezing, decides whether anything freezes at all.
Check in this order, and why
- Confirm whether the cabinet has an icemaker at all — A fill line and a module are the two things to look for. First because it is the top-ranked cause above and costs nothing.
- Check the door seal and where the frost is growing — Frost grows nearest where air is getting in. Second because its cause ranks second above.
- Look at the room, the sun and how often the door opens — Freezing is the first thing a loaded cabinet gives up. Third because its cause ranks third above.
What an owner can safely check
- Confirm what your cabinet is actually equipped with — Look for a fill line or an icemaker module before treating trays as a fault.
About 5 min
- Move it somewhere cooler for a day and compare — A few degrees of room temperature change what a small unit can hold.
About 30 min
- Check the door seal and clear any frost already formed — Frost grows from air leaking in; remove it and see whether it comes back.
Tools: soft clothAbout 30 min
- STOP HERE if the next step needs a panel off with the power on — That is where owner checks end and a service call begins.
Before you open anything
Safety
Switch the cabinet off at the breaker before reaching behind a panel, and close the water valve before disturbing any fitting on the supply line — a capacitor can hold a charge after the power is off, and a line under pressure will empty into the floor. Never thaw a frozen fill tube with an open flame or a heat gun; warm water and patience are the tools for that job.
When to call a technician
Call when the switch, the arm, the supply and the compartment temperature are all proven good and the maker still produces nothing — at that point the module or the valve is the remaining answer, and both sit behind a live panel. Call sooner if you find water where it should not be, because a leaking valve does damage while you wait. Tap, line and regulator parts come from draught suppliers; refrigeration parts come from the seller of the cabinet.
Nearest pages of this class
What this page does not cover
This page covers KEG refrigerators as a class, not one family or model line. Where a family- or model-specific page exists for your unit, that page is the more specific answer. Not here: harvest timings, module part numbers and fill volumes. It is draught cabinets built around a keg, a gas bottle and a tap tower rather than around shelves.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
