The short answer
The order that matters here is a drain that cannot clear the tub in time first, too much detergent, or the wrong kind next and the door lock losing confirmation mid-cycle last. A compact unit moves the ranking towards its installation: these are light machines that get relocated, stood on whatever is available, and squeezed into spaces that were never designed for them. That ranking is the value of this page: the cheap causes are the common ones on washers of this brand, and the costly one is what people reach for first.
What you observe
- The time remaining stands still or jumps up — Most machines extend a cycle while a condition is unmet rather than reporting it, so a stuck timer means waiting.
- It stalls at the same point every time — A repeatable stopping point names the step, and the step names the system — more useful than any code.
- It stops with water still in the drum — The machine has reached the drain step and cannot clear the tub in the time it allows.
- NEAR MISS — there is water on the floor as well — Read the leak page first. On many machines a leak detected under the base stops the cycle on purpose.
Causes, most likely first on this brand
- A drain that cannot clear the tub in time — Almost every mid-cycle stall on a washer is a drain that is too slow. First, and the rest of the order follows from it: it is the most common stall by a wide margin, and the pump filter is the one part of the drain path an owner can open.
- Too much detergent, or the wrong kind — A drum full of foam stops a machine reading its own water level, and the control responds by adding rinses and extending the cycle until it gives up. Next, and close behind the first: a cause this cheap to exclude belongs above anything that has to be dismantled.
- A load the machine cannot balance — Machines make several attempts to spread a load before giving up on the spin. Third, once the two above are clean: a machine that completes perfectly with a small even load has already told you the load was the fault.
- The door lock losing confirmation mid-cycle — Mid-cycle lock faults are intermittent by nature. Bottom of the list, deliberately: it is the cause that produces stalls with no pattern at all, and no pattern is itself a strong piece of evidence.
Check in this order, and why
- First: Open the pump filter and check the hose run — Have a tray ready; the chamber holds water. Then look behind the machine for a kink. It is first because it is the cheapest of the three to settle.
- Second: Run a rinse and spin with no detergent — Foam at the glass, or a cycle that suddenly behaves normally, names the detergent.
- Third: Redistribute the load and run a spin — A spin that completes with the same clothes spread out settles it without any tools.
What an owner can safely check
- Clear the pump filter and straighten the drain hose — Empty the filter chamber into a shallow tray, then check the hose for kinks and its height at the standpipe.
Tools: shallow tray, towelAbout 25 min
- Run a rinse-and-spin with an empty drum — No clothes and no detergent. Watch for foam appearing in the drum from what is left in the system.
About 45 min
- STOP HERE if the next step needs a meter on live terminals — That is the line between an owner check and a service call, and it is not worth crossing.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel, and treat every capacitor as still charged: a capacitor can hold a charge after the power is off. Never defeat the lid or door interlock to make a machine run with the door open — it cuts the drive for a reason, and a turning drum does not stop for a hand.
When to call a technician
Everything above that can be done with a tray and a towel is owner work; past that it is a service call. In particular, do not start replacing parts on a machine that stalls at a different point every time — that pattern points at the control side, and guessing at boards is how a cheap repair becomes an expensive one.
Nearest pages of this class
What this page does not cover
This is generalized information for Jieyang Airport District Xinan Anyou Electrical Appliance Factory washers as a class, not for one family or one model. No family- or model-specific page for this brand and appliance is published here yet, so nothing narrower is linked; when one is, it becomes the more specific answer and this page will point to it. Not here: wiring colours, torque figures, part numbers and panel-removal sequences, all of which differ by family.
