The answer first
On a Gasland refrigerator, water inside the cabinet almost always means a blocked defrost drain, and water on the floor usually means the same blockage overflowing forward. Both are owner-fixable with warm water and patience. A supply-line or inlet-valve leak is the less common cause but the more urgent one, because it does not stop on its own and it can run for hours unseen behind the cabinet.
What you are seeing
- Water at the back of the cabinet only — That is the supply side or the drain pan rather than the drain itself.
- A sheet of ice under the freezer floor panel — A drain that froze solid before it had a chance to overflow.
- NEAR MISS: everything is wet and nothing is cold — That is a unit that has stopped cooling and is defrosting itself, and it belongs on the cooling page.
Causes ranked for this machine
- A blocked defrost drain — Melt water that cannot reach the drain pan backs up, freezes into a shelf of ice under the liner, then runs forward under the crisper drawers. Ranked first on a Gasland refrigerator: this unit is carried, shaken and levelled by hand, so vibration and supply come before anything internal.
- A leaking water supply line or inlet valve — A compression fitting that has worked loose, or a line pinched when the cabinet was last pushed back, drips continuously at the back of the unit. Ranked second on a Gasland refrigerator: gas and water connections on a travelling appliance are worked loose by the road, which is why they come first.
- A cracked or displaced drain pan — The pan under the compressor is meant to hold the season of melt water while it evaporates; knocked out of its rails it simply tips the water onto the floor. Ranked third on a Gasland refrigerator: everything that is bolted, clamped or threaded on this unit has been shaken by the road, and that is where faults start.
What to check first, second and third
- Lift the crisper drawers and look for water or ice at the back of the liner — A pool or an ice sheet there is the drain, and it is the single most common cause on any refrigerator.
- Pull the unit out and look at the fitting where the water line enters it — A wet fitting or a damp patch on the floor directly beneath it is conclusive.
- Look under the cabinet for a wet trail leading back to the pan — Water at the back with a dry front and a clear drain points straight at the pan.
The checks you can make yourself
- Clear the drain hole at the back of the freezer floor with warm water and a soft tube — Never use a wire or anything sharp: the tubing below that hole is thin and punctures easily.
Tools: warm water, turkey baster or soft tubingAbout 30 min
- Dry the fitting completely, then watch it for a few minutes with the supply on — Any bead returning at the same point is the fitting; close the shut-off valve before touching it.
Tools: cloth, torchAbout 20 min
- STOP HERE once the drain runs clear, the pan is sound and the seals make contact — A tube inside the insulation or a cracked liner is a technician job and a warranty question.
Safety first
Safety
Water and electricity share the floor here, so switch off the breaker before mopping under or behind the cabinet, and unplug the unit before removing any panel — a capacitor can hold a charge after the power is off. Close the water shut-off valve before touching any fitting. Never clear a drain with a wire or a screwdriver: the tubing behind that hole punctures easily and turns a free fix into a sealed-system repair.
Where the owner job ends
Call once the drain runs clear, the pan is seated, the seals make contact and water still appears — at that point you are looking at a cracked liner, a failed inlet valve or a drain tube that has come adrift inside the cabinet. Call immediately for water anywhere near an outlet or an extension lead, and switch the breaker off before you go back to it.
Related pages for this machine
What is deliberately not here
This page covers the Gasland refrigerator as a class, not one family or model line. Part numbers, wiring colours, torque figures and panel fixings differ from build to build and are deliberately not here. Where a family- or model-specific page exists for your unit, that page is the more specific answer and should be read first.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
