What this usually is on these models
On the Alpicool ET refrigerator a complaint that reads as "it runs but nothing is cold" is far more often the supply the cabinet is running from than a failed compressor. The model record for this family is a single code, ET60, so everything below applies to one build rather than to a range of them.
What the owner actually sees
- It is plainly running, and nothing inside is cold — The compressor note is there and the panel is lit; the contents disagree with both.
- It never stops running — A healthy cabinet cycles. One that runs from morning to night is one that is never reaching the number it was set to.
- It pulls down overnight and gives it all back by the afternoon — That pattern points at the room and at the seal, not at the refrigeration.
- NEAR MISS — it is silent and dark — Nothing lit, nothing running: that is a power or start fault and belongs on a different page from this one.
What it usually turns out to be, in order
- The supply the cabinet is running from — First. A compressor draws several times its running current for the moment it starts. A thin extension lead, a tired socket or a long run sags at exactly that moment, the control sees the dip and shuts down to protect itself, and tries again a minute later. The panel stays lit throughout, which is why this gets mistaken for a dead cooling system. The record holds only ET60, so this check is the whole of the family's exposure to that cause.
- Heat that cannot leave the condenser — Second. A compressor refrigerator does not make cold, it moves heat, and only into air free to carry it away. Boxed into a cupboard, pushed against a wall or packed round with luggage, it breathes back the air it has just warmed, runs without stopping and never reaches setpoint.
- A loss in the sealed system — Last, always. It is the rarest of these causes and the only one that cannot be touched without recovery equipment and a licence. What it looks like is a machine trying hard and achieving nothing: long runs, a condenser that stays lukewarm, and a cabinet that drifts back up as fast as it comes down.
- Body: With one code recorded there is no older or newer build here to tell apart. With one build recorded and no split into older and newer machines to reason about, the order below is the order things can be eliminated in: the supply path first, because it takes a minute and because it produces the most convincing imitation of a dead cooling system.
Check in this order, and why
- Move it to a socket you trust, on a short lead — Nothing else you can do costs a minute and eliminates a whole branch of the fault tree. If the cabinet pulls down on the new socket, the machine was never the problem. On ET60 that is the whole of this step.
- Pull it clear and give the condenser open air — Leave it running in the open for an hour and watch whether the compressor starts cycling instead of running continuously. A cabinet that recovers in open air has an installation fault, not a refrigeration fault.
- Body: The record holds one code for this family, so the order below is not a model matrix — it is the order in which these causes can be eliminated on the machine in front of you, cheapest and least invasive first.
Safety first
Safety
Unplug the cabinet or switch off its breaker before removing any panel, and remember that a capacitor can hold a charge after the power is off. Nothing in this order requires getting inside. Never put a heat source near the coil to hurry a thaw, and never puncture frost with a knife or a screwdriver: the plate under it is thin, and what runs behind it is under pressure.
Models this page covers — The one model code recorded for this family.
Reference| Model number | Family key |
|---|---|
| ET60 | alpicool:refrigerator:et |
When to call a technician
Call once the checks above are clean: a cabinet on a sound supply, in open air, with a seal that grips and a setpoint you have set yourself, has a fault worth paying to diagnose. Call straight away, without working the list, if you can smell burning, if the compressor is tripping the protection in the room, or if there is oil anywhere on the tubing — oil outside the pipework means the system is open, and every hour it runs after that costs more to put right.
Other faults covered for this family
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
