Gas burner clicking nonstop? We clean and repair igniters, spark modules, and switches. Same-day service, 90-day warranty. Average repair cost: $80–$200. Some causes are DIY-fixable — see below.
Gas Stove continuous clicking repair typically costs $80 to $200. Some causes are DIY-fixable, but professional diagnosis is recommended if the problem persists. Most repairs are completed in 45 min-1 hour with a free diagnostic visit.
Persistent stove clicking in San Bruno follows the fog-belt pattern of moisture-driven igniter issues. Mid-century tract kitchens from 1958 without exhaust fans allow persistent humidity to saturate switch assemblies. CalWater soft water at 40 TDS keeps residue food-based. With 45,000 residents and 5 local repair providers, fog-related clicking is a common service call along the Peninsula corridor.
San Bruno shares the fog-belt clicking environment with Daly City and South San Francisco. Nearly 70-year-old tract kitchen igniter components have endured persistent moisture that corrodes electrodes and switch contacts. CalWater soft water at 40 TDS is helpful for cleaning but cannot prevent the fundamental moisture-driven sparking.
Moisture in igniter switch
Food debris in burner cap
Misaligned burner cap
Faulty spark module
Stuck igniter switch
Bay Area coastal humidity and fog create condensation on igniter switch contacts, completing the circuit that triggers continuous sparking. The clicking typically starts overnight or on foggy mornings and may stop as the kitchen warms. Boil-over liquid that seeps into the switch is another common trigger.
Cost: $60–$130 | Time: 30-60 minutes
Food particles and boil-over residue create conductive paths across the spark gap or switch contacts. The system interprets this as a continuous signal to spark. In Bay Area kitchens with frequent multi-burner cooking, spills onto the cooktop surface are a daily occurrence.
Cost: $40–$80 | Time: 20-40 minutes
The spark module's internal circuitry can short from moisture, creating a stuck-on condition. PG&E power surges can damage the module's timing circuit, causing continuous sparking rather than on-demand pulses. When the module fails, all burners click simultaneously.
Cost: $100–$200 | Time: 45-75 minutes
The wiring between the spark module and individual igniters can short from boil-over liquid, rodent damage, or heat degradation. A short creates a continuous signal to the module. The clicking may affect only certain burners or all of them depending on where the short occurs.
Cost: $80–$180 | Time: 45-90 minutes
| Detail | Range |
|---|---|
| Diagnostic | Free |
| Typical repair cost | $80–$200 |
| Repair time | 45 min-1 hour |
| Warranty | 90 days parts + labor |
Cost varies by root cause. Exact quote after free diagnostic visit.
Clicking repair in San Bruno costs $80 to $200. The 5 local fog-belt providers handle this issue frequently. Sealed module upgrades are recommended.
In San Bruno, salt-laden marine air and persistent fog deposit corrosive moisture on metal surfaces and electronics. This can affect your appliance's thermocouple: salt deposits on the thermocouple tip create an insulating layer, causing flame-sensing failures and gas shutoff Clean the thermocouple tip with fine emery cloth annually; never use water or cleaning solutions
In San Bruno, sustained relative humidity above 60% promotes mold growth, condensation on cold surfaces, and accelerated corrosion. This can affect your appliance's igniter electrode: moisture on the ceramic igniter insulator allows the spark to track down the side instead of jumping to the burner, preventing ignition Dry the electrode and surrounding area if the burner fails to light; a hair dryer on low can remove trapped moisture
In San Bruno, very low mineral content (<60 ppm tds) or sodium-softened water causes over-sudsing, rubber swelling, and reduced detergent rinsing. This can affect your appliance's oven interior: soft water steam clean cycles leave a sodium residue film on interior surfaces that can smoke during subsequent cooking Use distilled water for steam clean functions; wipe interior with a damp cloth after the cycle completes
Free diagnostic visit for continuous clicking issues. Same-day appointments available in San Bruno.
Book Free DiagnosticReviewed by James Okonkwo, Kitchen Appliance & Gas Systems Technician