Want a regional phone & address? Pick your area.
LG·dishwasherlow severity
LG Error Code bE
Improper detergent / not level
Common Causes
- 1Wrong detergent
- 2Unit not level
Step-by-Step Troubleshooting
- 1
Check that you are using automatic dishwasher detergent — hand dish soap causes massive suds overflow in dishwashers
- 2
If suds are visible inside the tub, cancel the cycle and add 1/2 cup of cooking oil or run the unit through several rinse cycles to break down the foam
- 3
Place a bubble level on the front edge of the dishwasher tub (door open) to check side-to-side level, then on the side edge for front-to-back level
- 4
Adjust the front leveling legs by turning them clockwise (raise) or counterclockwise (lower) until the unit is level
Pro Diagnostic Tip
The bE code on LG dishwashers doubles as a tilt sensor alert. If the unit was jostled during installation or the floor has settled (common in California homes on post-tension slabs), the tilt sensor triggers. Re-leveling resolves it without any part replacement.
You Might Also Notice
- •Suds visible through door window
- •Water pooling on one side of tub
- •Door not sealing evenly
- •Dishes on one rack not getting clean
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$0–$50
Parts + labor. Free diagnosis with repair.
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Use correct detergent and level the unit
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code bE disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
$89 → $0 Service Call & Diagnosis — offer ends May 31
Frequently Asked Questions
What does LG error code bE mean?
LG error code bE indicates: Improper detergent / not level. This is a low-severity issue affecting your dishwasher.
How do I fix LG error code bE?
Check that you are using automatic dishwasher detergent — hand dish soap causes massive suds overflow in dishwashers Then, If suds are visible inside the tub, cancel the cycle and add 1/2 cup of cooking oil or run the unit through several rinse cycles to break down the foam Then, Place a bubble level on the front edge of the dishwasher tub (door open) to check side-to-side level, then on the side edge for front-to-back level There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error bE?
Besides the error code on the display, common signs include: Suds visible through door window; Water pooling on one side of tub; Door not sealing evenly. If you notice any of these symptoms, check your dishwasher's display panel for error code bE.
How much does it cost to fix LG bE?
Repair costs for LG bE typically range from $0 to $50 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.