Want a regional phone & address? Pick your area.
GE·Washermedium severity
GE Error Code E2
Drain error
Common Causes
- 1Clogged drain filter
- 2Kinked drain hose
- 3Drain pump blockage
Have towels ready when opening the drain filter — residual water will spill out. Sacramento hard water can leave calcium deposits in the drain pump impeller.
Step-by-Step Troubleshooting
- 1
Cancel the cycle and unplug the washer
- 2
Locate the drain filter (bottom-front behind access panel) and clean debris
- 3
Check drain hose for kinks — straighten and ensure proper height (under 96 inches)
- 4
Inspect drain hose end inside standpipe for blockage
- 5
Run a spin-only cycle to test drain function
- 6
If water still does not drain, test drain pump motor for continuity (expect 5-15 ohms)
Pro Diagnostic Tip
Bay Area homes with older plumbing often have partially clogged standpipes that cause intermittent E2. Test by disconnecting the drain hose and draining into a bucket — if it drains fine, the blockage is in the home plumbing, not the washer.
You Might Also Notice
- •Water remains in tub after cycle
- •Washer stops mid-cycle with water inside
- •Slow or incomplete draining
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$50–$250
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WH23X28418 drain pump assemblyWH41X26871 drain hose
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Diagnose the root cause, test affected components with calibrated meters, replace faulty parts with OEM replacements, and verify proper operation through a full test cycle.
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E2 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
$89 → $0 Service Call & Diagnosis — offer ends May 31
Frequently Asked Questions
What does GE error code E2 mean?
GE error code E2 indicates: Drain error. This is a medium-severity issue affecting your washer.
How do I fix GE error code E2?
Cancel the cycle and unplug the washer Then, Locate the drain filter (bottom-front behind access panel) and clean debris Then, Check drain hose for kinks — straighten and ensure proper height (under 96 inches) There are 3 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error E2?
Besides the error code on the display, common signs include: Water remains in tub after cycle; Washer stops mid-cycle with water inside; Slow or incomplete draining. If you notice any of these symptoms, check your washer's display panel for error code E2.
How much does it cost to fix GE E2?
Repair costs for GE E2 typically range from $50 to $250 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.