Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

GE washer E4 is an unbalanced-load error causing shaking. See how to rebalance, level the washer, and the modest up-to-$180 repair cost.

Hotpoint dishwasher C1 means the base-pan leak sensor tripped — the float rose on collected water. Disconnect power first. DIY checks and a $125–$300 range.

Hotpoint dishwasher C3 means the drain pump is not clearing the tub — usually a matted filter or fouled impeller. Owner-fixable steps and a $100–$225 range.

Hotpoint dishwasher C4 means the tub did not fill in time — usually a part-closed supply valve or a scaled inlet screen. Owner-fixable steps and a $75–$200 range.

Hotpoint dishwasher C7 means the wash motor is not running. Causes include a jammed impeller. Professional repair runs $200–$375.

Hotpoint dishwasher C8 means the wash water never heats up — usually a burned-open heating element or blown thermal fuse. DIY signs and a $125–$275 range.

Hotpoint dryer AF is an airflow restriction warning — clean the lint screen and vent. Often owner-fixable; professional cost up to $125.

Hotpoint dryer E1 means the exhaust thermistor is open. Causes, a simple resistance test, and a $75–$175 professional repair range.

Hotpoint dryer E2 means the exhaust sensor shorted low, feeding a false cold reading so the drum runs too hot. Treat it as urgent. DIY signs and a $75–$175 range.

Hotpoint dryer E3 is an over-temperature fault — a fire-safety code. Clear the vent first. Causes and a $100–$300 professional repair.

Hotpoint dryer E4 is a heater relay fault — unplug it immediately. A stuck relay is a fire hazard. Board repair runs $175–$350.

Hotpoint dryer E8 means the drive motor will not run — an open winding or a burnt centrifugal start switch. DIY signs and a $175–$375 professional range.

Hotpoint oven F0 is a stuck-key fault on the range control — often moisture behind the keypanel. Cut power if it self-heats. DIY drying and a $175–$375 range.

Hotpoint oven F2 means the oven ran past its temperature ceiling — a fire-safety code. Cut power and stop using it. DIY steps and a $100–$350 range.

Hotpoint oven F3 means the oven RTD sensor read open — often just a backed-off rear plug. DIY reseat, safe checks, and a $50–$150 professional range.

Hotpoint oven F7 means one function pad is reading held — usually a single delaminating pad on the touch overlay. DIY checks and a $100–$275 range.

Hotpoint oven F8 is a clock/timer (ERC) failure, often after a power surge. Causes and a $175–$350 control board repair.

Hotpoint refrigerator CC is a condenser fan fault — often just dust on the blade. Causes and a $100–$225 professional repair range.

Hotpoint refrigerator CI is an ice maker fault — often low water pressure, not the module. Causes and a $125–$300 professional repair.

Hotpoint refrigerator CO means the boards stopped exchanging data — often a cracked conductor in the top-hinge harness. DIY reset and a $175–$400 range.

Hotpoint refrigerator dH means the defrost cycle is not clearing frost — usually a burned-open heater. DIY signs, safe thawing, and a $125–$275 range.

Hotpoint refrigerator FF means the evaporator fan stalled — often a blade frozen in ice pointing at a defrost fault. DIY signs and a $100–$250 range.

Hotpoint washer dE means the door was not confirmed latched — often a worn lock gear on the GE-built front-loader. DIY checks and a $100–$225 range.

Hotpoint washer E1 means a water level pressure switch error. Causes, safe DIY checks, and a $75–$200 repair cost from a Bay Area technician.

Hotpoint washer E2 is a drain timeout — usually a clogged drain filter. Clean-it-yourself steps plus a $100–$225 professional repair range.

Hotpoint washer E3 means spin speed was not reached — usually an unbalanced load. Easy owner fixes and a repair cost of up to $250.

Hotpoint washer E4 is an overfill safety code — water level too high. Turn off the supply first. Causes and a $125–$275 professional repair.

Hotpoint washer tE means the wash-water temperature is out of range — often just a shut hot tap, not the sensor. DIY checks and a $75–$175 range.

Hotpoint washer UE means spin balance was not achieved — usually an uneven load. A free rearrange fixes most cases. DIY steps and an up-to-$200 range.

KitchenAid dishwasher showing F1E1? It means an open water-temperature sensor. What causes it, the DIY checks, and whether it is worth fixing.
Let our professional technicians help. Same-day service available.