Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Thermador Star Burner clicking and won’t stop? Moisture in the ignition wells is the usual cause. How to dry it out, plus spark-module and igniter-switch diagnostics for Thermador gas cooktops.
Learn the warning signs of appliance repair scams and overcharging. From phantom part replacements to inflated diagnostic fees, here's how to protect yourself.

The top cause of a Samsung fridge 'not defrosting' is the drain re-freezing, not a defrost failure. Run forced defrost (Fd) to see if the heaters work. Twin Cooling has two circuits.

Samsung refrigerator running constantly? Usually a defrost fault, a leaking door seal, dirty coils, or a cold setting. Here is how to find why.

Samsung fridge temperature off? The display shows what the thermistor reports, not reality — so a drifted sensor reads "37°F" while the interior sits warmer. Verify with an independent thermometer first, then match the pattern to the fault.

A Samsung fridge tripping the breaker is usually a shorted start relay, a compressor ground fault, a shorted board, or an overloaded circuit. When it trips reveals which. EasyBear.

Samsung washer stuck mid-cycle? With no mechanical timer, the board stalls whenever a sensor reports out-of-range — so the number the display freezes at tells you which sensor. 1 minute means drain; time jumping back means rebalance; frozen fill means the pressure tube.

A Samsung washer not heating starts with one question — does your model have an internal heater? If it does, an HE code points to the thermistor or element. EasyBear guide.

A Samsung washer overflows when it can't sense water level — a third of the time it's just a kinked or clogged pressure tube. Then the inlet valve, transducer, or board. OE code explained.

A burning smell from a Samsung washer means something is overheating. Unplug it, read the odor, and use our ranked cause table to find the board, motor, belt, or pump at fault.

A blank Samsung washer display is usually a break between its two boards — a lost power feed, the communication cable, or the display sub-board. Here's how to isolate it.

A Samsung washer missing hot or cold water usually has a burned-out inlet-valve coil, a closed tap, or a clogged screen. First rule out a normal EcoBubble cold cycle.

Rust on a Samsung fridge is often not rust at all — iron dust that wipes off — but black-stainless coatings genuinely peel. Here is how to tell, and what actually fixes each.

A completely dead Samsung refrigerator — no lights, no display, no fans — usually traces to the main control board. Here is the fault map and how to check each cause.

A Samsung washer that seems to ignore your temperature setting is often EcoBubble washing cold by design. Here is how to tell that from a real fault — a dead solenoid, swapped hoses, or a bad thermistor.

Six of the noises a Samsung makes have both a normal version and a fault version, and each pair differs by one detail — a rhythm, a duration, or whether the sound stops the moment you open the door.

A loud Samsung washer is usually a foreign object in the drain pump, a worn tub bearing, or a cracked spider arm. Use the noise character and timing to pinpoint the part, with a ranked cause table, the exact Samsung part numbers, and DIY checks.

Samsung washer tripping your circuit breaker or GFCI? Diagnose ground faults from water intrusion, motor winding shorts, and heater element leakage.

A Samsung washer that walks is telling you its VRT balance ring can't contain the spin — worn steel balls on an older machine, or shipping bolts left in on a new one. Leveling and shocks round out the list.

A Samsung washer timer that won't advance is a stalled cycle, not a broken clock. The board freezes wherever a sensor check fails — most often an incomplete drain near the end that ends in 5E.

A Samsung washer that won’t lock or unlock is usually a failed wax-motor lock, then harness corrosion or a misaligned strike. Ranked causes, the lock part number, and safe checks before replacing the latch assembly.

Most likely: the unit isn't level. Samsung's heavy French-door models concentrate weight up top, so an uneven leg lets the fridge rock with every compressor cycle. Loose compressor mounts, a worn condenser fan (DA31-00028E), or floor resonance are the other usual causes…

Most likely: mineral buildup on Samsung's small-orifice inlet valve seat lets water seep past even with the machine off. One test settles it — unplug the washer: if water still enters, the valve failed; if only when plugged in, a stuck control-board relay holds it open. Shut the supply valves first…

Most likely: spider arm corrosion inside a front-load WF Samsung washer — the aluminum spider (DC97-16509A) dissolves against the stainless drum and sheds rust onto your laundry. The boot-seal "rust" and cabinet spots most owners also see are cosmetic, so telling the three apart is the whole diagnosis…

When a Samsung refrigerator's defrost heater stops heating, frost builds on the evaporator and cooling suffers. Twin Cooling Plus uses two independent heaters. How to run Forced Defrost, spot a cracked glass-tube heater, and check the PCB relay.

A Samsung washer that pumps water out but won't spin points to the spin side, not the pump — a fractured spider arm, a failed hall sensor, a broken belt on top-loaders, or a door lock lost mid-cycle. The causes ranked for WF and WA models.

Most likely: the washer is not level or the shipping bolts were left in, but on Samsung the VRT balance ring is a distinctive cause — flat-spotted balls or leaked damping fluid. Diagnosis for leveling, bolts, the balance ring, and shock absorbers.

Samsung refrigerator won’t dispense water? A frozen door line is the top cause, then a clogged or aftermarket filter, a failed dispenser solenoid, or an air lock. Two quick tests plus ranked fixes.

A Samsung washer that fills slowly or not at all usually has a clogged inlet screen, a weak valve, or a pressure-sensor fault — often shown as a 4E code. Here is the fix path.

A Samsung washer door that will not open is usually the wax-motor lock refusing to release because the drum is spinning, water remains, or power was lost. Here is how to release it safely.
Let our professional technicians help. Same-day service available.