Want a regional phone & address? Pick your area.
Frigidaire·Washermedium severity
Frigidaire Washer Error Code E44
Door lock detection failure
Common Causes
- 1Feedback switch not reporting the thrown bolt
- 2Broken conductor in the lock-signal run
- 3Corroded board connector eating the confirmation signal
Step-by-Step Troubleshooting
- 1
The key distinction here is that the bolt actually throws — you can hear and see it latch — but the control never gets word that it did, so this is a lost-signal hunt, not a stuck-lock hunt
- 2
Meter the lock feedback switch for a clean change of state as the bolt seats; a switch that latches mechanically yet never toggles electrically is exactly what leaves the board blind
- 3
Walk the signal wire from the latch back to the board looking for a nicked conductor or a backed-out pin where the loom flexes with the door
- 4
Study the board-end plug for the green film that steam-borne moisture grows on the pins, since a corroded contact drops the confirmation even with a perfect switch and wire
Pro Diagnostic Tip
Prove the bolt moves before you touch the latch: if it visibly locks yet the fault stands, the fault is in the confirmation path — switch, wire, or connector — not the lock body. Chase the wiring and the board plug first, because swapping the whole latch does nothing for a broken feedback line.
You Might Also Notice
- •Bolt latches then the machine reports it open
- •The lock and detection faults trade off cycle to cycle
- •Starts then halts within a few seconds of locking
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$125–$250
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
134550800 door lock assembly137221600 wiring harness
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E44 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Frigidaire error code E44 mean?
Frigidaire error code E44 indicates: Door lock detection failure. This is a medium-severity issue affecting your washer.
How do I fix Frigidaire error code E44?
The key distinction here is that the bolt actually throws — you can hear and see it latch — but the control never gets word that it did, so this is a lost-signal hunt, not a stuck-lock hunt Then, Meter the lock feedback switch for a clean change of state as the bolt seats; a switch that latches mechanically yet never toggles electrically is exactly what leaves the board blind Then, Walk the signal wire from the latch back to the board looking for a nicked conductor or a backed-out pin where the loom flexes with the door There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error E44?
Besides the error code on the display, common signs include: Bolt latches then the machine reports it open; The lock and detection faults trade off cycle to cycle; Starts then halts within a few seconds of locking. If you notice any of these symptoms, check your washer's display panel for error code E44.
How much does it cost to fix Frigidaire E44?
Repair costs for Frigidaire E44 typically range from $125 to $250 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online