Want a regional phone & address? Pick your area.
Electrolux·Washerhigh severity
Electrolux Washer Error Code E52
Motor signal error
Common Causes
- 1Motor signal loss
- 2Control board fault
- 3Wiring issue
Step-by-Step Troubleshooting
- 1
Check motor position sensor (tachometer/hall sensor) on back of motor
- 2
Measure tachometer resistance — typically 100-300 ohms
- 3
Inspect wiring between motor and inverter board for damage
- 4
If tachometer tests good, the inverter board is not reading the signal — replace board
Pro Diagnostic Tip
E52 means the board commands the motor but gets no feedback (speed) signal; if the motor still spins freely by hand and the windings test good, the tachometer coil has failed — a small, inexpensive part behind the motor rotor. This differs from E50 (a genuine motor or bearing failure): with E52 the motor is healthy but blind, so the board pulses it and gives up. On Perfect Steam direct-drive units the tach coil sits under the rotor and is cheap to swap once the rotor is off, so never replace the motor for E52 until the coil and its connector are ruled out.
You Might Also Notice
- •Motor starts then stops abruptly
- •Drum spins erratically then quits
- •Spin speed varies wildly during the cycle
- •Washer clicks and retries the spin repeatedly
- •Long pauses before the drum builds any speed
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$150–$400
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
134372600 — Motor tachometer/sensor134743500 — Motor control board
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code E52 is a high-severity issue that can cause further damage to your washer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Electrolux error code E52 mean?
Electrolux error code E52 indicates: Motor signal error. This is a high-severity issue affecting your washer.
How do I fix Electrolux error code E52?
Check motor position sensor (tachometer/hall sensor) on back of motor Then, Measure tachometer resistance — typically 100-300 ohms Then, Inspect wiring between motor and inverter board for damage There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error E52?
Besides the error code on the display, common signs include: Motor starts then stops abruptly; Drum spins erratically then quits; Spin speed varies wildly during the cycle. If you notice any of these symptoms, check your washer's display panel for error code E52.
How much does it cost to fix Electrolux E52?
Repair costs for Electrolux E52 typically range from $150 to $400 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related Electrolux Washer Error Codes
Call NowAvailable 24/7 — call or textBook Online