Want a regional phone & address? Pick your area.
Electrolux·Washermedium severity
Electrolux Washer Error Code E10
Water fill problem
Common Causes
- 1Water supply turned off
- 2Inlet hose kinked
- 3Inlet valve clogged
Step-by-Step Troubleshooting
- 1
Verify both hot and cold supply valves are fully open
- 2
Remove inlet hoses and clean mesh screen filters
- 3
Check household water pressure — LuxCare wash system needs 20-120 PSI
- 4
Inspect inlet valve for mineral buildup (common in hard-water areas)
Pro Diagnostic Tip
E10 is a "no/low water" fault raised before the machine ever reaches level, so it is almost always supply-side — a closed valve, a kinked hose, or a scaled inlet screen — rather than an internal failure. On Electrolux EFLS models with SmartBoost premix there is a second clue: if only the premix chamber fails to fill while the main tub fills normally, the dedicated boost solenoid has failed, not the main inlet valve. E10 differs from E11 in that E11 starts filling and times out low, while E10 sees essentially no water arrive.
You Might Also Notice
- •Cycle starts but the drum stays dry
- •Very long fill times before anything happens
- •Only hot or only cold water enters
- •A faint buzz from the valve with no water flow
- •Machine pauses at the start of the cycle waiting to fill
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$50–$180
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
137353500 — Water inlet valve (Electrolux front-load)5304515673 — Inlet hose screens (4-pack)
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Check water supply
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E10 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Electrolux error code E10 mean?
Electrolux error code E10 indicates: Water fill problem. This is a medium-severity issue affecting your washer.
How do I fix Electrolux error code E10?
Verify both hot and cold supply valves are fully open Then, Remove inlet hoses and clean mesh screen filters Then, Check household water pressure — LuxCare wash system needs 20-120 PSI There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error E10?
Besides the error code on the display, common signs include: Cycle starts but the drum stays dry; Very long fill times before anything happens; Only hot or only cold water enters. If you notice any of these symptoms, check your washer's display panel for error code E10.
How much does it cost to fix Electrolux E10?
Repair costs for Electrolux E10 typically range from $50 to $180 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related Electrolux Washer Error Codes
Call NowAvailable 24/7 — call or textBook Online