KitchenAid KRMF Refrigerator — Issues & Fixes

This guide pulls the KRMF platform into one place: the models that share it, the parts that wear out, the codes it throws, its recall standing, and a plain repair-or-replace call based on the unit's age. The aim is a fast, honest read: what fails, what it costs you in downtime, and whether a fix is still the smart move.

KRMF at a glance#

KRMF706ESS, KRMF706EBS, KRMF706EWH, KRMF706EPA all sit on the KRMF chassis; a fix proven on one applies to the rest.

Common problems on the KRMF#

These are the faults that account for the bulk of KRMF service calls:

Ice maker frost buildup causing complete shutdown. What you'll see: Whirlpool platform ice maker issue. Expect it in near 24% of the repairs logged on this platform. Catch it early and the repair usually stays contained.

Preserva dual evaporator fan motor failure. In the field: one compartment warm while other is fine. It accounts for roughly 14% of KRMF service calls. Diagnosing it promptly keeps the fix small.

Measured Fill dispenser solenoid sticking. Symptom: overfills or will not stop dispensing. On the KRMF it lands at about 12% of repair visits, and the measured fill dispenser solenoid is the component to check first. Catching it early keeps the repair small.

Main control board relay failure. The tell — compressor short-cycles on and off. Expect it in near 10% of the repairs logged on this platform, and the first check belongs on the main control board relay. It is easier to resolve before the fault spreads.

Door gasket losing seal at French door center gap. What you'll see: warm air infiltration. It accounts for roughly 8% of KRMF service calls. Diagnosing it promptly keeps the fix small.

Error codes to know#

Panel codes on the KRMF and where to read the full walkthrough:

• Error PO — full diagnosis and fix
• Error DOOR AJAR — full diagnosis and fix
• Error CF — full diagnosis and fix

A code that is not listed often clears with a 60-second power cut at the breaker; if it returns, it needs a real diagnosis.

Parts that fail most#

The KRMF wear parts, with the numbers to order:

Recall status#

No active recalls stand against the KRMF as of 2026-05-28. Recalls can post at any time, so check cpsc.gov by model number and sign up for alerts.

Repair or replace?#

For the KRMF, a unit under 10 years old is almost always worth fixing when the repair runs below 50% of a replacement. Past 10 years, total up the last two-to-three years of repairs and lean toward a new unit once that sum clears 40% of replacement cost — you also reset the warranty clock.

Maintenance that heads off these failures#

Most KRMF failures above are preventable with routine care:

• Replace the EveryDrop Filter 4 every 6 months — restricted flow triggers ice maker frost
• Clean condenser coils behind base grille every 6 months
• Defrost the ice maker zone manually if frost exceeds 1/4 inch
• Test both compartment fans quarterly — listen for fan noise from fridge and freezer separately
• Clean the Measured Fill dispenser nozzle monthly to prevent mineral buildup

Making the KRMF last#

To maximize the lifespan of your refrigerator, keep the interior temperature at 37 degrees F for the fresh food compartment and 0 degrees F for the freezer. Avoid overloading — restricted airflow around food items forces the compressor to work harder. Set a calendar reminder to replace the water filter every 6 months and clean the condenser coils every 6-12 months. These two maintenance tasks alone can add years to your refrigerator's service life and prevent the most common failures.

Related guides#

• Kitchenaid Refrigerator Ice Maker Not Making Ice
• Kitchenaid Refrigerator Not Cooling
• Kitchenaid Refrigerator Not Dispensing Water
• Kitchenaid Refrigerator Frost Ice Buildup

When you would rather hand it off, book a KRMF refrigerator repair: upfront pricing before any work and a 90-day warranty on parts and labor.