Quick Answer: Resetting a Maytag Dishwasher#
A Maytag dishwasher runs the Whirlpool platform with a heavier PowerBlast cycle, so reset it at the breaker and hold the power off two minutes — slightly longer than a plain Whirlpool. That lets the board and its wash-motor relay clear before you restore power. It will not mend a blocked drain or a door latch that has failed.
How to Reset a Maytag Dishwasher (Step by Step)#
- Maytag dishwashers run the Whirlpool control platform but pair it with the PowerBlast cycle, so start by cutting power at the breaker or under-sink switch.
- Keep the power off for two minutes — a touch longer than a Whirlpool reset — to let the Maytag board and its heavier wash-motor relay clear before you restore power.
- To dump a stuck cycle, press and hold the Start/Resume pad, which doubles as cancel on Maytag tubs, for three seconds until the pump runs out.
- If the console is locked, hold the Control Lock pad for three seconds until the padlock light clears, then confirm the Start/Resume pad responds.
Do You Have the Right Tools?
Water pressure gauge ($60), spray arm tester, float switch multimeter ($85), and drain inspection camera. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Maytag Dishwasher Model Variations#
Top-control Maytag models hide the Start/Resume and Control Lock pads on the top door edge, while front-control JetClean tubs show both on the console. The Start/Resume pad also serves as cancel on Maytag machines, so one button both resumes and dumps a cycle. A surviving fault cross-checks against Whirlpool codes because the two share the board.
When a Reset Doesn't Fix Your Maytag Dishwasher#
A start light that keeps blinking after the reboot is usually a door-latch or drain issue rather than the electronics. Decode any code with our Maytag error-code guide, then follow the dishwasher-not-draining, will-not-start, and blinking-start-light symptom pages. Because the board mirrors Whirlpool, the same fault list applies once you have ruled out the latch and the pump.
Safety First — Know the Risks
Live 120V wiring in a wet environment is one of the most dangerous DIY scenarios. Water + electricity = serious shock risk. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Need Professional Help?#
If a power-cycle and the checks above do not bring your Maytag dishwasher back, book a free diagnostic and an EasyBear technician will take it from there.
Maytag Dishwasher Reset FAQ#
How do I reset a Maytag dishwasher?
Cut power at the breaker or under-sink switch and keep it off for two minutes so the board and wash-motor relay fully clear, then restore it. That extra minute over a Whirlpool reset matters on the heavier PowerBlast machines.
How do I use the Start/Resume button on a Maytag dishwasher?
A press starts or resumes the selected cycle, and holding it for a few seconds during a wash cancels and drains the tub. Maytag doubles cancel onto that one pad.
Why is the start light blinking on my Maytag dishwasher?
A blinking start light usually flags a door that is not fully latched or a drain that cannot clear, stored as a fault. Confirm the latch and drain before assuming the reset failed.
Where is the Control Lock on a Maytag dishwasher?
It is a dedicated pad marked with a padlock, on the top door edge for top-control models or the console for front-control JetClean tubs. Hold it about three seconds until the lock light clears.
Why will my Maytag dishwasher not drain?
Trapped water usually means a clogged filter, a kinked hose, or a blocked air gap rather than a board fault. Clean the filter and check the hose before testing the pump.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
