Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Samsung dryer thumping, squealing, or scraping? Each sound points to a specific part — rollers, belt, glides, blower, or motor. A sound-to-cause guide.

Samsung dryer running but not drying? A restricted vent and contaminated moisture sensors cause most weak-heat cases. Ranked causes and the vent-disconnect test.

Samsung dishwasher not dispensing detergent? The wax-motor door didn’t open — usually a blocking dish or hardened residue, sometimes the actuator. How to tell it apart from a fill problem and fix it.

Samsung dishwasher won’t fill and showing 1E? The fault is on the supply side — a half-closed valve, kinked hose, clogged inlet screen, low pressure, or a failed inlet valve. DIY-friendly checks, ranked.

A Samsung ice maker that stops is most often a freeze-up, then the inlet valve, then the assembly. Identify your version first, then follow the ranked fix path.

Miele dishwasher leaving residue? Spray arm, AutoDos, and circulation pump diagnostics for Miele G7000, G5000, and Classic series dishwashers.

Miele heat pump or vented dryer squealing, thumping, or rattling? Drum bearing, belt, and blower diagnostics for Miele T1 and Classic series dryers.

Miele heat pump or vented dryer not heating? F55 filter error, heating element, and heat exchanger diagnostics for Miele T1 and Classic series dryers.

Miele built-in refrigerator not cooling? Compressor, DynaCool fan, and PerfectFresh zone diagnostics for Miele K2000 and MasterCool series. Learn about...

Miele front-load washer grinding, banging, or vibrating? Drum bearing, shock absorber, and spider arm diagnostics for Miele W1 and Classic series.

Miele washing machine not spinning? Motor control, door lock (F34/F35), and drain pump diagnostics for Miele W1 and Classic series front-load washers.

A Samsung dishwasher that stops mid-cycle logged a code first — 5E for drain, HE for heat, LE for a leak, or a silent stop that points at the DD81-01629A door latch.

Samsung dishwasher error code displayed? Samsung dishwashers communicate faults through specific error codes on the LED display — 5E/SE (drain failure).

Samsung dishwasher leaving dishes wet? Learn about AutoRelease door, heating element, rinse aid, and vent fan issues specific to Samsung DW80R and DW80K models.

Samsung dishwasher stopping mid-cycle? Identify the phase it dies in to pin the fault — drain 5E, heat HE1, or fill — and know which need a technician.

A blank Samsung dishwasher display is usually a lost power feed, a failed control board, or a worn touchpad — not dead glass. The SmartThings app can help isolate it before tools.

A burning smell from a Samsung dishwasher is usually a motor straining against a clog, melted plastic on the heating element, or an electrical fault on the DW80 control board. Here is how to tell them apart safely, ranked by likelihood.

Miele dryer cycles running 2-3 hours? Lint filter, heat exchanger, and moisture sensor diagnostics for Miele heat pump and vented dryers. Expert tips and costs.

A leaking Samsung dishwasher is usually a worn door gasket, a leak at the sump or spray-arm seal, or a drain-hose connection. This guide traces the leak by where the water appears and covers overfilling and door-seal faults on DW80 models.

A Samsung dishwasher not cleaning dishes is usually clogged spray-arm nozzles or water that isn't hot enough, then a worn wash-motor impeller or dispenser issue. This guide ranks the causes on DW80 models and shows how to clear the arms and check water temperature.

A Samsung dishwasher not drying is most often an empty rinse-aid dispenser, since Samsung relies on condensation drying, then a weak heating element (HE1), a stuck AutoRelease door, poor loading, or a tripped high-limit thermostat. Code-led diagnosis and DIY checks.

A Samsung dishwasher not heating is most often a failed heating element (often HE1), then a tripped high-limit thermostat, a drifted 50K thermistor, a control-board heat relay, or scale insulating the element. Code-led diagnosis for the DW80 families and DIY tests.

Most likely: water is not leaving the tub fast enough, so it backs up — a drain-side restriction (a clogged filter or the DD31-00005A drain pump) or the base-tray leak float being tripped. Samsung's error codes point straight at the subsystem: a 5E means the drain did not clear within eight…

A Miele oven running hot or cold is usually a drifting temperature sensor or a calibration offset after a power interruption. Causes, how convection and Moisture Plus affect the reading, and safe checks before a service call.

A noisy Samsung dishwasher is most often the drain pump, a spray arm hitting a dish, or debris in the sump. Ranked causes matched to the sound, the quick checks you can do, and when a pump or motor needs service.

Most likely: the detergent dispenser door is being blocked or jammed, so the pod or powder never drops into the wash and dishes come out dirty. A tall dish against the door, hardened detergent gluing it shut, or a failed door actuator are the usual causes…

Most likely: the integrated latch-and-switch assembly (DD81-01629A) has a cracked plastic actuator, or its switch has failed while the latch still holds — so the dishwasher looks powered but refuses every Start. The click test tells you which: two clicks good, one click a dead switch, zero clicks a broken latch…

Most likely: the blinking lights are an error code, not a random fault — a flashing pattern such as 5E (drain), 1E (water supply), or HE1 (heating) points straight at a subsystem. Read the code in SmartThings or diagnostic mode, then clean the filters or check the named part before opening anything up…

Most likely: the door bellow has been torn by a trapped coin or underwire, or a Waterproof-system hose connection is seeping. Diagnosis for the bellow, hose, coin trap, and tub seal on Miele front-load washers.

Most likely: the tub thermistor has drifted and is feeding the board a wrong temperature, or the heating element is weak. Diagnosis for the thermistor, element (HE1), a clogged filter, and the DW80 control board on Samsung dishwashers.
Let our professional technicians help. Same-day service available.