Want a regional phone & address? Pick your area.
Samsung·Dishwashermedium severity
Samsung Dishwasher Error Code tE
Temperature sensor error
Common Causes
- 1Thermistor failure
Step-by-Step Troubleshooting
- 1
Access the thermistor from below the tub by removing the base plate and lower access panel. The sensor is typically mounted in the sump area near the heater
- 2
Disconnect the thermistor leads and test with a multimeter: at room temperature (77 °F), the resistance should be approximately 10-15 k-ohm. Significantly different readings indicate a failed sensor
- 3
Inspect the wiring from the thermistor to the control board. The humid dishwasher environment can corrode connector pins over time
- 4
If the thermistor and wiring test good, the main control board temperature sensing circuit may be faulty
Pro Diagnostic Tip
Samsung dishwasher tE codes that appear intermittently (sometimes triggers, sometimes runs fine) usually indicate a loose connector rather than a failed thermistor. The vibration from the wash pump jiggles the connector loose. Secure the connection with dielectric grease on the pins and a zip tie on the harness.
You Might Also Notice
- •Dishwasher not heating water
- •Cycle runs cold throughout
- •Extended cycle times as the machine attempts to reach temperature
- •Sanitize light not illuminating
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$125–$300
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Temperature sensor/thermistor (Samsung DD32-00010A)Main control board (Samsung DD82-01139A) if sensor tests normal
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code tE disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends May 31
Frequently Asked Questions
What does Samsung error code tE mean?
Samsung error code tE indicates: Temperature sensor error. This is a medium-severity issue affecting your dishwasher.
How do I fix Samsung error code tE?
Access the thermistor from below the tub by removing the base plate and lower access panel. The sensor is typically mounted in the sump area near the heater Then, Disconnect the thermistor leads and test with a multimeter: at room temperature (77 °F), the resistance should be approximately 10-15 k-ohm. Significantly different readings indicate a failed sensor Then, Inspect the wiring from the thermistor to the control board. The humid dishwasher environment can corrode connector pins over time There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error tE?
Besides the error code on the display, common signs include: Dishwasher not heating water; Cycle runs cold throughout; Extended cycle times as the machine attempts to reach temperature. If you notice any of these symptoms, check your dishwasher's display panel for error code tE.
How much does it cost to fix Samsung tE?
Repair costs for Samsung tE typically range from $125 to $300 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.