Want a regional phone & address? Pick your area.
Samsung·Dishwashermedium severity
Samsung Dishwasher Error Code 1E
Clogged filter / water level sensor
Common Causes
- 1Clogged filter
- 2Sensor issue
Step-by-Step Troubleshooting
- 1
Remove the bottom rack and turn the cylindrical filter assembly counterclockwise to remove it. Clean all food debris from both the fine mesh filter and the coarse filter
- 2
With the filter removed, use a sponge to clean the filter well area at the bottom of the dishwasher tub. Check for broken glass or hard debris that may block the drain path
- 3
Locate the water level sensor float (a small plastic dome near the front-left of the tub floor). Lift it up and down — it should move freely. Clean any debris underneath that prevents it from floating properly
- 4
If the filter is clean and the float moves freely, the pressure switch or turbidity sensor may be faulty. These are accessed by removing the lower access panel beneath the door
Pro Diagnostic Tip
Samsung dishwasher 1E codes after a recent kitchen renovation are almost always caused by construction debris (plaster dust, sawdust) in the filter. A thorough vinegar rinse cycle (2 cups on the top rack, empty machine, hot cycle) clears the residue.
You Might Also Notice
- •Dishwasher stops mid-cycle
- •Water not draining properly between cycles
- •Dishes not getting clean due to restricted water flow
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$100–$225
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Fine mesh filter assembly (Samsung DD82-01542A) if filter is damagedWater level float/sensor (Samsung DD81-02176A) if float mechanism is broken
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clean the dishwasher filter
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code 1E disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends May 31
Frequently Asked Questions
What does Samsung error code 1E mean?
Samsung error code 1E indicates: Clogged filter / water level sensor. This is a medium-severity issue affecting your dishwasher.
How do I fix Samsung error code 1E?
Remove the bottom rack and turn the cylindrical filter assembly counterclockwise to remove it. Clean all food debris from both the fine mesh filter and the coarse filter Then, With the filter removed, use a sponge to clean the filter well area at the bottom of the dishwasher tub. Check for broken glass or hard debris that may block the drain path Then, Locate the water level sensor float (a small plastic dome near the front-left of the tub floor). Lift it up and down — it should move freely. Clean any debris underneath that prevents it from floating properly There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error 1E?
Besides the error code on the display, common signs include: Dishwasher stops mid-cycle; Water not draining properly between cycles; Dishes not getting clean due to restricted water flow. If you notice any of these symptoms, check your dishwasher's display panel for error code 1E.
How much does it cost to fix Samsung 1E?
Repair costs for Samsung 1E typically range from $100 to $225 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.