Want a regional phone & address? Pick your area.
Maytag·Washermedium severity
Maytag Washer Error Code F9 E1
Drain not completed in the allotted window
Common Causes
- 1Coin trap and pump filter packed with debris
- 2Corrugated drain hose kinked at the standpipe
- 3Foreign object wedged in the impeller vanes
- 4Drain hose shoved so deep it back-siphons
Step-by-Step Troubleshooting
- 1
Pop the small toe-panel door low on the front of the MHW and unthread the coin-trap filter, catching the gush in a shallow pan
- 2
Lay towels first — a stalled drain leaves the sump full and it pours out the moment the trap turns
- 3
Run a hand along the drain hose to the standpipe or laundry sink, freeing any crimp that throttles the outflow
- 4
Make sure the hose enters the standpipe only a few inches; buried too deep it siphons and never satisfies the timer
- 5
With trap and hose clear, listen for the pump to whine dry — no outflow means a chipped impeller and a pump swap
Pro Diagnostic Tip
The pump trap on a Maytag front-loader is a magnet for coins, hairpins, and stray underwires, so a quarterly trap-out heads off most of these drain faults. A pump that howls but moves no water has lost impeller vanes to one of those objects and gets replaced outright rather than cleaned again.
You Might Also Notice
- •Rinse water still standing in the drum at cycle end
- •The pump grinds away far longer than usual
- •Loads finish heavy and dripping wet
- •A stagnant, swampy smell rising from the sump
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$100–$250
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W11510712 Drain Pump MotorW10906534 Drain Hose Extension Kit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clear the pump trap behind the toe panel
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F9 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F9 E1 mean?
Maytag error code F9 E1 indicates: Drain not completed in the allotted window. This is a medium-severity issue affecting your washer.
How do I fix Maytag error code F9 E1?
Pop the small toe-panel door low on the front of the MHW and unthread the coin-trap filter, catching the gush in a shallow pan Then, Lay towels first — a stalled drain leaves the sump full and it pours out the moment the trap turns Then, Run a hand along the drain hose to the standpipe or laundry sink, freeing any crimp that throttles the outflow There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F9 E1?
Besides the error code on the display, common signs include: Rinse water still standing in the drum at cycle end; The pump grinds away far longer than usual; Loads finish heavy and dripping wet. If you notice any of these symptoms, check your washer's display panel for error code F9 E1.
How much does it cost to fix Maytag F9 E1?
Repair costs for Maytag F9 E1 typically range from $100 to $250 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online