Want a regional phone & address? Pick your area.
Maytag·Washerlow severity
Maytag Washer Error Code F0 E2
Excess suds detected
Common Causes
- 1Over-dosed detergent for the load size
- 2Standard non-HE detergent foaming in a sealed HE drum
- 3Gummed dispenser dumping its whole charge at once
- 4Sluggish drain leaving old suds to compound into the next load
Step-by-Step Troubleshooting
- 1
Drop to an HE-rated detergent — a conventional formula whips up several times the foam inside a sealed Maytag front-load drum
- 2
Meter detergent to the low HE line molded on the cap, roughly a tablespoon for a normal load, and skip the eyeball pour
- 3
Run the Clean Washer with affresh cycle empty to purge foam still clinging in the sump and door-boot folds
- 4
Twist out the drain-pump filter behind the toe kick and rinse the felt of trapped suds and softener sludge
Pro Diagnostic Tip
Maytag 6th Sense infers suds from the motor-current signature during tumble, so it trips this fault when foam makes the basket slip. On the MHW front-loaders the real repeat offender is a lazy drain that never fully evacuates rinse water, so if the code returns after you correct the detergent, treat it as a partial pump-filter or drain-hose restriction rather than a soap habit.
You Might Also Notice
- •A ring of foam creeping past the door boot
- •The machine bolting on unrequested extra rinses
- •Laundry that still feels slick or soapy coming out
- •A sour, closed-up smell in the drum between loads
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$0–$175
Parts + labor. Free diagnosis with repair.
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Use HE detergent and reduce amount
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F0 E2 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F0 E2 mean?
Maytag error code F0 E2 indicates: Excess suds detected. This is a low-severity issue affecting your washer.
How do I fix Maytag error code F0 E2?
Drop to an HE-rated detergent — a conventional formula whips up several times the foam inside a sealed Maytag front-load drum Then, Meter detergent to the low HE line molded on the cap, roughly a tablespoon for a normal load, and skip the eyeball pour Then, Run the Clean Washer with affresh cycle empty to purge foam still clinging in the sump and door-boot folds There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F0 E2?
Besides the error code on the display, common signs include: A ring of foam creeping past the door boot; The machine bolting on unrequested extra rinses; Laundry that still feels slick or soapy coming out. If you notice any of these symptoms, check your washer's display panel for error code F0 E2.
How much does it cost to fix Maytag F0 E2?
Repair costs for Maytag F0 E2 typically range from $0 to $175 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online