Want a regional phone & address? Pick your area.
Maytag·Washerhigh severity
Maytag Washer Error Code F1 E2
Motor control unit error
Common Causes
- 1Motor control board failure
- 2Power surge damage
- 3Overheating from restricted ventilation
Disconnect power before inspecting the MCU. Capacitors can hold a charge for several minutes after unplugging.
Step-by-Step Troubleshooting
- 1
Unplug the washer for 5 minutes to allow a full control board reset
- 2
Check the wire harness between the MCU and CCU for loose or corroded connections
- 3
Inspect the MCU board (beneath the washer near the motor) for burn marks or swollen capacitors
- 4
Measure voltage output from the MCU to the motor — should match cycle phase requirements
- 5
Replace the MCU if diagnostics confirm board failure
Pro Diagnostic Tip
On the Maytag MVWB VMW (Vertical Modular Washer) platform, the MCU is mounted beneath the washer near the motor. Power surges are the primary killer — a triac short on the MCU often causes this code without visible board damage.
You Might Also Notice
- •Washer completely unresponsive to start command
- •Motor hums but drum does not turn
- •Burning smell from beneath the washer
- •Intermittent power-on failures
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$200–$400
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W10756692 Motor Control Board (MCU)W10888578 Wire Harness (MCU-to-CCU)
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F1 E2 is a high-severity issue that can cause further damage to your washer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends May 31
Frequently Asked Questions
What does Maytag error code F1 E2 mean?
Maytag error code F1 E2 indicates: Motor control unit error. This is a high-severity issue affecting your washer.
How do I fix Maytag error code F1 E2?
Unplug the washer for 5 minutes to allow a full control board reset Then, Check the wire harness between the MCU and CCU for loose or corroded connections Then, Inspect the MCU board (beneath the washer near the motor) for burn marks or swollen capacitors There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error F1 E2?
Besides the error code on the display, common signs include: Washer completely unresponsive to start command; Motor hums but drum does not turn; Burning smell from beneath the washer. If you notice any of these symptoms, check your washer's display panel for error code F1 E2.
How much does it cost to fix Maytag F1 E2?
Repair costs for Maytag F1 E2 typically range from $200 to $400 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.