Want a regional phone & address? Pick your area.
Maytag·Washerlow severity
Maytag Washer Error Code F8 E2
Dispenser motor fault
Common Causes
- 1Detergent buildup in dispenser mechanism
- 2Dispenser motor failure
- 3Dispenser actuator jammed
Step-by-Step Troubleshooting
- 1
Remove the dispenser drawer and clean all detergent and fabric softener residue with hot water
- 2
Run hot water through the dispenser housing to dissolve buildup in the internal channels
- 3
Check that the dispenser actuator moves freely by hand — it should click between positions
- 4
If the motor still does not operate after cleaning, replace the dispenser motor assembly
Pro Diagnostic Tip
On Maytag MHW front-loaders, fabric softener and liquid detergent residue hardens inside the dispenser housing over time, jamming the actuator. Monthly cleaning with hot water prevents this. If the actuator gear teeth are stripped, the entire motor assembly must be replaced.
You Might Also Notice
- •Detergent not dispensed during wash cycle
- •Fabric softener remains in dispenser after cycle
- •Grinding noise from dispenser area during fill
- •Clothes not getting clean despite adequate detergent
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W11310982 Dispenser Motor AssemblyW11165548 Dispenser Drawer Assembly
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clean dispenser drawer
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F8 E2 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends May 31
Frequently Asked Questions
What does Maytag error code F8 E2 mean?
Maytag error code F8 E2 indicates: Dispenser motor fault. This is a low-severity issue affecting your washer.
How do I fix Maytag error code F8 E2?
Remove the dispenser drawer and clean all detergent and fabric softener residue with hot water Then, Run hot water through the dispenser housing to dissolve buildup in the internal channels Then, Check that the dispenser actuator moves freely by hand — it should click between positions There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F8 E2?
Besides the error code on the display, common signs include: Detergent not dispensed during wash cycle; Fabric softener remains in dispenser after cycle; Grinding noise from dispenser area during fill. If you notice any of these symptoms, check your washer's display panel for error code F8 E2.
How much does it cost to fix Maytag F8 E2?
Repair costs for Maytag F8 E2 typically range from $75 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.