Want a regional phone & address? Pick your area.
Maytag·Washermedium severity
Maytag Washer Error Code F8 E1
Fill flow not detected in time
Common Causes
- 1A supply tap left part-closed behind the machine
- 2Hose pinched where it loops to the wall
- 3Silted inlet screens starving the valve
- 4House pressure sagging below the fill minimum
- 5Inlet valve solenoid gone weak or open
Step-by-Step Troubleshooting
- 1
Trace both braided hoses to the wall and crank each tap wide — a half-turned valve is the quiet cause here
- 2
Back the hoses off the machine and lift out the little cone screens, rinsing away the grit that hard water packs into the mesh
- 3
Gauge house pressure at a nearby hose bib; a Maytag fill stalls when it drops under the low twenties and expects the forties to sixties
- 4
Ohm each inlet solenoid coil at the valve body and confirm it lands in the few-hundred to low-thousands range rather than open
- 5
Peer into the valve ports for the chalky calcium crust that valley water lays down and throttles flow
Pro Diagnostic Tip
Valley hard water furs up the inlet screens inside a couple of years, so make a twice-yearly screen rinse part of routine care. Once scale has grown inside the valve body itself, no cleaning brings it back and the valve is replaced whole. A stall that only affects one temperature usually means just that one solenoid has quit.
You Might Also Notice
- •The tub takes a quarter hour or more to reach level
- •Water only dribbles in where it should gush
- •One temperature fills while the other stays dry
- •The fill window times out and the machine dumps and quits
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$225
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W11165546 Water Inlet Valve AssemblyW10838615 Inlet Hose Screen Kit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Open both taps and clear the inlet screens
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F8 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F8 E1 mean?
Maytag error code F8 E1 indicates: Fill flow not detected in time. This is a medium-severity issue affecting your washer.
How do I fix Maytag error code F8 E1?
Trace both braided hoses to the wall and crank each tap wide — a half-turned valve is the quiet cause here Then, Back the hoses off the machine and lift out the little cone screens, rinsing away the grit that hard water packs into the mesh Then, Gauge house pressure at a nearby hose bib; a Maytag fill stalls when it drops under the low twenties and expects the forties to sixties There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F8 E1?
Besides the error code on the display, common signs include: The tub takes a quarter hour or more to reach level; Water only dribbles in where it should gush; One temperature fills while the other stays dry. If you notice any of these symptoms, check your washer's display panel for error code F8 E1.
How much does it cost to fix Maytag F8 E1?
Repair costs for Maytag F8 E1 typically range from $75 to $225 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online