Want a regional phone & address? Pick your area.
Maytag·Washerhigh severity
Maytag Washer Error Code F7 E1
Rotor position feedback fault
Common Causes
- 1Rotor position sensor (RPS) failed or heat-cracked
- 2Broken lead between the RPS and the motor control
- 3Direct-drive motor winding fault
- 4Loose stator-to-control connector
Step-by-Step Troubleshooting
- 1
Cut power and lay the washer back to reach the pancake motor bolted to the rear of the outer tub
- 2
Unplug the rotor position sensor riding on the stator and inspect its little three-pin connector for spread or greened pins
- 3
Read the RPS across its terminals — a healthy Hall-type sensor lands in the ten-to-fifteen-thousand-ohm band
- 4
Turn the rotor slowly by hand and watch the meter twitch evenly as the magnet ring sweeps past the sensor
- 5
With the sensor proven, look to the motor control for a driver stage that no longer reads the feedback pulses
Pro Diagnostic Tip
On Maytag direct-drive washers the rotor position sensor gives out far more often than the motor it watches, and it is a small, inexpensive Hall part rather than the pricey motor — so always meter it first. A common failure mode on the MHW stator is a heat-cracked sensor magnet that reads fine cold but loses the rotor once the wash warms up.
You Might Also Notice
- •The motor turns yet the basket never climbs to spin speed
- •The washer aborts right as high-speed extraction begins
- •The fault shows only on heavier, wetter loads
- •A steady hum with the basket sitting still
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$200–$450
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WPW10178988 Rotor Position Sensor (RPS)W10677715 Drive Motor AssemblyW10756692 Motor Control Board (MCU)
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F7 E1 is a high-severity issue that can cause further damage to your washer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F7 E1 mean?
Maytag error code F7 E1 indicates: Rotor position feedback fault. This is a high-severity issue affecting your washer.
How do I fix Maytag error code F7 E1?
Cut power and lay the washer back to reach the pancake motor bolted to the rear of the outer tub Then, Unplug the rotor position sensor riding on the stator and inspect its little three-pin connector for spread or greened pins Then, Read the RPS across its terminals — a healthy Hall-type sensor lands in the ten-to-fifteen-thousand-ohm band There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error F7 E1?
Besides the error code on the display, common signs include: The motor turns yet the basket never climbs to spin speed; The washer aborts right as high-speed extraction begins; The fault shows only on heavier, wetter loads. If you notice any of these symptoms, check your washer's display panel for error code F7 E1.
How much does it cost to fix Maytag F7 E1?
Repair costs for Maytag F7 E1 typically range from $200 to $450 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online