Want a regional phone & address? Pick your area.
Maytag·Washerlow severity
Maytag Washer Error Code F0 E1
Load detected during the Clean Washer cycle
Common Causes
- 1Laundry left in the basket when the maintenance cycle started
- 2A heavy towel or mat fooling the load-sensing routine
- 3Suds or trapped water read as a load
- 4Load-sense calibration drifted on an aging machine
Step-by-Step Troubleshooting
- 1
Open the washer and remove everything from the basket, since the Clean Washer with affresh routine must run completely empty to scrub the tub
- 2
Wipe the door boot and check the sump is not holding old rinse water that the control can misread as a partial load
- 3
Restart the Clean Washer cycle with no detergent pod and only the affresh tablet or a measured dose of bleach as the manual directs
- 4
If the code returns on a truly empty drum, run a normal cycle to confirm load sensing is otherwise working before suspecting the pressure system
Pro Diagnostic Tip
This is an operating reminder far more often than a fault: Maytag blocks the tub-clean routine whenever it senses weight so the affresh chemistry is not wasted on laundry. If it persists on an empty basket, treat it as a load-sensing or pressure-sensor drift and pair it with any F3 water-level codes before replacing hardware.
You Might Also Notice
- •The Clean Washer cycle refuses to begin
- •The code clears the moment the drum is emptied
- •The maintenance reminder keeps reappearing
- •Extra rinses trigger on ordinary loads
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$0–$175
Parts + labor. Free diagnosis with repair.
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Empty the drum and restart the Clean Washer cycle
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F0 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F0 E1 mean?
Maytag error code F0 E1 indicates: Load detected during the Clean Washer cycle. This is a low-severity issue affecting your washer.
How do I fix Maytag error code F0 E1?
Open the washer and remove everything from the basket, since the Clean Washer with affresh routine must run completely empty to scrub the tub Then, Wipe the door boot and check the sump is not holding old rinse water that the control can misread as a partial load Then, Restart the Clean Washer cycle with no detergent pod and only the affresh tablet or a measured dose of bleach as the manual directs There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F0 E1?
Besides the error code on the display, common signs include: The Clean Washer cycle refuses to begin; The code clears the moment the drum is emptied; The maintenance reminder keeps reappearing. If you notice any of these symptoms, check your washer's display panel for error code F0 E1.
How much does it cost to fix Maytag F0 E1?
Repair costs for Maytag F0 E1 typically range from $0 to $175 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online