Want a regional phone & address? Pick your area.
Maytag·Dishwashermedium severity
Maytag Dishwasher Error Code F9 E1
Drain took longer than allowed
Common Causes
- 1Drain hose crimped at the disposer or cabinet
- 2Disposer knockout plug never punched out
- 3Weak or worn drain pump
- 4Missing high loop letting the line siphon
Step-by-Step Troubleshooting
- 1
Trace the ribbed drain hose beneath the sink and straighten any crimp, especially at the disposer inlet spigot
- 2
On a disposer hookup, be sure the molded knockout slug was driven out at install — a blind inlet dams the whole drain
- 3
Confirm the hose loops up to the counter underside or ties into an air gap so tub water cannot back-siphon
- 4
Scrub the in-tub filter and finger the sump for the grit that slows a marginal pump below the timeout
- 5
Spin the disposer for a moment to flush any sludge sitting in the shared drain branch
Pro Diagnostic Tip
The single most missed cause of a slow Maytag drain is the disposer knockout plug: whoever fits the garbage disposal has to punch out the dishwasher nipple, and when they forget, rinse water has nowhere to go and creeps out over the timeout. Verify that plug is gone before chasing anything electrical.
You Might Also Notice
- •The tub empties in a slow crawl at the end of the run
- •A shallow puddle lingers on the cavity floor
- •A gurgle sounds from the sink drain during pump-out
- •Lower-rack dishes rinse dirty in the backwashed water
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$225
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WPW10730972 Drain PumpW10906535 Drain Hose Kit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Free the drain hose and disposer inlet
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F9 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F9 E1 mean?
Maytag error code F9 E1 indicates: Drain took longer than allowed. This is a medium-severity issue affecting your dishwasher.
How do I fix Maytag error code F9 E1?
Trace the ribbed drain hose beneath the sink and straighten any crimp, especially at the disposer inlet spigot Then, On a disposer hookup, be sure the molded knockout slug was driven out at install — a blind inlet dams the whole drain Then, Confirm the hose loops up to the counter underside or ties into an air gap so tub water cannot back-siphon There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F9 E1?
Besides the error code on the display, common signs include: The tub empties in a slow crawl at the end of the run; A shallow puddle lingers on the cavity floor; A gurgle sounds from the sink drain during pump-out. If you notice any of these symptoms, check your dishwasher's display panel for error code F9 E1.
How much does it cost to fix Maytag F9 E1?
Repair costs for Maytag F9 E1 typically range from $75 to $225 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online