Want a regional phone & address? Pick your area.
Maytag·Dishwashermedium severity
Maytag Dishwasher Error Code F6 E1
No water detected at fill
Common Causes
- 1Household supply stop closed or barely cracked
- 2Clogged inlet-valve screen on hard-water lines
- 3Kinked fill line behind the tub
- 4Failed water-inlet valve solenoid
Step-by-Step Troubleshooting
- 1
Reach under the adjacent sink and confirm the dishwasher supply stop is fully open, since a half-turned valve starves the fill on a Maytag PowerBlast cycle
- 2
Close the supply, disconnect the fill line at the valve, and clear the fine mesh inlet screen that traps grit from area hard water
- 3
Straighten any pinch in the braided fill line where it loops behind the MDB tub after an install or a repair
- 4
With power off, read the inlet-valve solenoid for continuity and treat an open coil as a failed valve rather than a supply problem
Pro Diagnostic Tip
Maytag routes fill through a flood-float and the inlet valve, so a stuck-up float mimics this code by blocking the fill signal; lift and drop the foam float in the tub floor before condemning the valve. On homes with old galvanized plumbing the inlet screen re-clogs, so fit a sediment filter to stop repeat calls.
You Might Also Notice
- •The cycle starts but no water enters
- •A faint buzz at the valve with no flow
- •Dishes come out dry and dirty
- •The cycle stretches far past its normal length
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$90–$260
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water-inlet valveInlet screen
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Confirm the supply valve is open and the inlet screen is clear
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F6 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code F6 E1 mean?
Maytag error code F6 E1 indicates: No water detected at fill. This is a medium-severity issue affecting your dishwasher.
How do I fix Maytag error code F6 E1?
Reach under the adjacent sink and confirm the dishwasher supply stop is fully open, since a half-turned valve starves the fill on a Maytag PowerBlast cycle Then, Close the supply, disconnect the fill line at the valve, and clear the fine mesh inlet screen that traps grit from area hard water Then, Straighten any pinch in the braided fill line where it loops behind the MDB tub after an install or a repair There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F6 E1?
Besides the error code on the display, common signs include: The cycle starts but no water enters; A faint buzz at the valve with no flow; Dishes come out dry and dirty. If you notice any of these symptoms, check your dishwasher's display panel for error code F6 E1.
How much does it cost to fix Maytag F6 E1?
Repair costs for Maytag F6 E1 typically range from $90 to $260 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online