Want a regional phone & address? Pick your area.
Amana·Washermedium severity
Amana Washer Error Code F8 E1
Water fill timeout
Common Causes
- 1Water supply valves closed
- 2Inlet screens clogged
- 3Inlet hoses kinked
- 4Inlet valve failure
Step-by-Step Troubleshooting
- 1
Make sure both hot and cold taps behind the Amana washer are cranked fully open before anything else
- 2
Unthread the fill hoses and pick out the little mesh screens at the valve inlets — hard water scale packs them solid on these value-line machines
- 3
Sanity-check pressure at a nearby faucet; an Amana wants roughly 40 to 60 PSI and starts timing out below 20
- 4
Ohm each fill solenoid coil around 500 to 1500 ohms — a dead coil is why only one temperature fills
- 5
Feel and look inside the valve body for chalky calcium; a valve scaled internally will not open fully and needs replacing whole
Pro Diagnostic Tip
F8 E1 is a fill-timeout, so on a budget Amana it is nearly always the supply side — a lazy tap, a scaled screen, or a tired valve — rather than the electronics. The fine inlet screens are the choke point because hard water fills them with scale in a couple of years, so a twice-yearly screen clean keeps this code away. If one temperature fills and the other will not, chase that side’s solenoid instead of the shared screens.
You Might Also Notice
- •Fill drags past fifteen minutes
- •Water only dribbles in
- •Hot fills but cold will not, or the reverse
- •Fill times out and the washer dumps what it took
- •Long silent pause at the start with no water
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water inlet valve assemblyInlet hose screen kit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Check water supply valves are open
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F8 E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Amana error code F8 E1 mean?
Amana error code F8 E1 indicates: Water fill timeout. This is a medium-severity issue affecting your washer.
How do I fix Amana error code F8 E1?
Make sure both hot and cold taps behind the Amana washer are cranked fully open before anything else Then, Unthread the fill hoses and pick out the little mesh screens at the valve inlets — hard water scale packs them solid on these value-line machines Then, Sanity-check pressure at a nearby faucet; an Amana wants roughly 40 to 60 PSI and starts timing out below 20 There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F8 E1?
Besides the error code on the display, common signs include: Fill drags past fifteen minutes; Water only dribbles in; Hot fills but cold will not, or the reverse. If you notice any of these symptoms, check your washer's display panel for error code F8 E1.
How much does it cost to fix Amana F8 E1?
Repair costs for Amana F8 E1 typically range from $75 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online