F10E5 in brief
Maytag lists F10E5 with a potential cause of a diverter leak: the diverter, the valve that routes wash water between the spray arms, is not sealing as it should. Pressure meant for one arm can bleed to the other, so both racks wash weakly, and water that escapes at the diverter can drop into the base pan beneath the tub, where many dishwashers have a sensor that reacts by stopping the cycle and running the drain pump. That is why F10E5 can arrive with a half-finished cycle and a pump that keeps going. Switch the dishwasher off, check the floor and the base, give the base time to dry out, and check for foam. If the code returns once the base is dry, the diverter needs repairing. A wet floor is worth photographing before you mop, in case damage needs reporting later.
Error codes
Reference| Code | Meaning |
|---|---|
| F10E5 | Potential Cause: Diverter Leak |
What happens with F10E5
- The cycle halts and the pump keeps running — The machine is trying to empty itself because water reached the base.
- Dishes left wet and partly washed — The programme stopped early, or pressure meant for one spray arm bled away to the other.
- Water on the floor under the door — The base pan can overflow at the front.
- Foam visible through the door gap — Suds can push water past seals.
- The code clears after a day, then returns — The base dried, but the leak is still there.
- Standing water glimpsed behind the kick plate — You may see it through the gap at the bottom; look, but do not reach in.
Ranked causes of F10E5
- A diverter seal that has failed — First: the seal at the valve hardens and starts to let water past.
- Foam from the wrong detergent — Second: suds force water where it should not go.
- A cracked part in the diverter area — Third: cracks leak every time the pump runs.
- A loose hose or clamp nearby — Fourth: water from a nearby joint lands in the same base pan.
Dealing with water in the base
- Switch off at the breaker — Before touching any water near the dishwasher.
- Check for suds — Foam means changing the detergent before anything else.
- Mop the floor at the front — Note how much water came out.
- Let the base dry — Leave the power off and the door slightly open for a day.
- Run a short rinse and watch — If the code returns quickly, the leak is real and ongoing.
- Check the rinse aid dispenser — An overfilled or leaking dispenser adds foam to every wash.
Owner steps for F10E5
- Switch off at the breaker and mop up — Dry the floor around the dishwasher.
Tools: towelsAbout 10 min
- Leave the base to dry for a day — Keep the power off and the door a little open.
Tools: ::
- Rinse away any suds — Use a short rinse without detergent once the base is dry.
About 20 min
- Use only dishwasher detergent — Hand-washing liquid makes foam that causes leaks.
Tools: ::
- Book a repair if F10E5 returns — The diverter seal or housing is replaced from beneath the tub with water and power off.
Tools: ::
Safety with a leaking dishwasher
Water and mains wiring meet at the base of the dishwasher, so switch off at the breaker before mopping. Never tilt the machine to empty its base. Wet floors are a slip hazard, so dry them promptly. Never bypass the door switch, and leave the lower panel in place; parts behind it can hold a charge.
When F10E5 needs a professional
Book a repair if F10E5 returns after the base has dried and the detergent is right, if both racks keep washing weakly, or if water reaches the floor again. A professional replaces the diverter seal or housing and checks the hoses and clamps nearby. Mention any foam you saw and the detergent you use, since that changes what is checked first.
Scope of the F10E5 page
This reading covers Maytag built-in dishwashers that list F10E5. Other Maytag appliances and other brands are outside it. No model-specific F10E5 page exists yet; base pans and leak sensors differ between models, so consult your model's documentation.

