Amana Washer F0 E2 Error Code: Causes, Cost & Fix

What is the Amana Washer F0 E2 error?#

F0 E2 on an Amana washer is an excess-suds error: on these value NTW and NFW tubs the fill volume is very low, so even a little too much detergent — or any non-HE soap — whips into a mountain of foam the machine cannot rinse away, and it keeps adding rinses to chase it. It is not a breakdown, and the margin for detergent error is just tiny. Measuring one level tablespoon of HE detergent clears it at no cost, so that is the first thing I have owners try before looking at any part.

F0 E2 on a Amana Washer: likely causes and repair cost#

On a Amana Washer, the F0 E2 code signals: excess suds.

Typical professional repair: up to $130 · Difficulty: easy · often owner-fixable

Fastest thing to try first: Reduce detergent.

Symptoms that often accompany F0 E2: Foam creeping out around the lid or door seal; Extra rinse phases padding out the cycle; Laundry that feels soapy or slick when done; A sour smell lingering between loads; Suds still visible through the glass at rinse

Technician diagnostic sequence for F0 E2:

1. Drop to a single tablespoon of HE detergent — the low fill volume on these value Amana NTW and NFW tubs whips even a little soap into a mountain of foam
2. If regular soap has been used, run two empty rinse cycles to purge the built-up lather before trusting the machine again
3. Fire a Clean Washer or tub-clean cycle to strip the slimy film that clings inside the basket and hoses
4. Pull and rinse the drain pump filter, since foam that cannot drain away keeps re-tripping the code
5. Only if F0 E2 keeps coming back on correct detergent, have the pressure sensor hose checked for reading the foam layer as a high water level

Parts a technician may check or replace: Pressure sensor; Drain pump filter

Field note: On these budget Amana top and front loaders the tub fills with very little water, so the margin for detergent error is tiny — a heaping scoop or any non-HE soap overwhelms the small water volume and foams over, and simply measuring one level tablespoon clears it at no cost. A stubborn F0 E2 that survives correct detergent is the rare case: a lazy drain leaving foam behind, or a pressure hose misreading that foam as water, which is the only part of this that costs anything.

How to troubleshoot the F0 E2 error yourself#

Fix the detergent first, because that is the whole problem in most cases. Drop to a single tablespoon of HE detergent — the low fill volume on these tubs foams over on anything more. If regular, non-HE soap has been used, run two empty rinse cycles to purge the built-up lather before trusting the machine again. Fire a Clean Washer or tub-clean cycle to strip the slimy film that clings inside the basket and hoses and keeps generating foam. Then pull and rinse the drain pump filter, since foam that cannot drain away keeps re-tripping the code. All of that is owner-level and usually free. Only if F0 E2 keeps coming back on correct HE detergent should the pressure-sensor hose be checked for reading the foam layer as a high water level, and that testing is a technician's call.

Is the Amana Washer F0 E2 error worth fixing?#

This is barely a repair. The overwhelming majority of F0 E2 faults come down to detergent dosing and clear for free by measuring HE soap correctly and cleaning the trap. In the rare case it survives correct detergent, the only paid part is a pressure sensor, which sits under the modest ceiling in the table above. There is no scenario where F0 E2 justifies replacing the washer — it is a dosing and maintenance issue first, and a minor sensor repair at worst.

Amana Washer F0 E2: frequently asked questions#

What does the F0 E2 error mean on a Amana Washer?#

It means the washer sensed more suds than it can rinse away. On these low-fill tubs, too much detergent or non-HE soap is almost always the cause, so the machine keeps adding rinses to clear the foam.

Is it safe to keep using a Amana Washer that shows the F0 E2 error?#

It is safe to run, just slow — the machine keeps padding the cycle with rinses and laundry may finish feeling soapy. There is no hazard, only wasted time and water until you cut the detergent.

Can I clear the F0 E2 error myself, or do I need a technician?#

You can almost always clear it yourself: use one tablespoon of HE detergent, run a Clean Washer cycle, and rinse the drain filter. Only a code that survives all that needs a technician to check the pressure sensor.

How much does it cost to repair the F0 E2 error on a Amana Washer?#

Usually it costs nothing — correcting detergent and cleaning the trap resolves most cases. If it persists on proper HE dosing, the pressure-sensor repair is the only paid part, up to about $130.

Which parts usually fail when a washer throws the F0 E2 code?#

Most of the time nothing has failed — it is a detergent-dosing issue on a low-fill tub. When a real part is involved, it is the pressure sensor misreading the foam as a high water level.

Is a Amana Washer with the F0 E2 error worth repairing?#

There is rarely anything to repair — correct dosing fixes it for free. On the odd persistent case the minor pressure-sensor fix is worth it. F0 E2 is never a reason to replace the machine.

Why does too much detergent trigger the F0 E2 error?#

These tubs use very little water, so excess or non-HE detergent whips into more foam than the machine can rinse out. Sensing suds it cannot clear, the washer keeps adding water and rinses, and posts F0 E2.