Want a regional phone & address? Pick your area.
Maytag·Microwavemedium severity
Maytag Microwave Error Code FC E3
The appliance could not connect to the router.
Common Causes
- 1There may a problem with the due to connection time out, poor signal strength, a failed router, the Wi-Fi Module in the appliance, or the associated wiring.
- 2Is your smart phone, or tablet operating correctly?
Step-by-Step Troubleshooting
- 1
Power appliance down by turning off the circuit breaker(s) for one (1) minute.
- 2
Power appliance up by turning on the circuit breaker(s).
- 3
Monitor the appliance for one (1) minute to ensure the error code does not display again.
- 4
Verify appliance operation.
- 5
Reset your wireless router.
- 6
If yes, disconnect power from router for 2 minutes, then re-connect power to router, then disconnect power to the appliance for 2 minutes, and reconnect.
- 7
Move your router to a different location in your home
- 8
Contact your Internet Service Provider
Do You Have the Right Tools?
High-voltage capacitor discharge tool ($90), magnetron tester ($200), microwave leakage detector ($150). Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Power appliance down by turning off the circuit breaker(s) for one (1) minute.
This repair requires high-voltage discharge tools, magnetron testers, and microwave leakage detectors. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
Microwave capacitors store lethal voltage (4,000V+) even when unplugged. This is the single most dangerous DIY appliance repair. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code FC E3 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code FC E3 mean?
Maytag error code FC E3 indicates: The appliance could not connect to the router.. This is a medium-severity issue affecting your microwave.
How do I fix Maytag error code FC E3?
Power appliance down by turning off the circuit breaker(s) for one (1) minute. Then, Power appliance up by turning on the circuit breaker(s). Then, Monitor the appliance for one (1) minute to ensure the error code does not display again. There are 5 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How much does it cost to fix Maytag FC E3?
Repair costs for Maytag FC E3 typically range from $100 to $500 depending on the specific cause. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related Maytag Microwave Error Codes
Demo ModeIf demo mode was recently turned on or off "dOn" or "dOff" will show in the display.mediumE03The Keypad (User Interface) reported a problem to the control board.mediumE11The Gas Sensor reported a problem to the control board.mediumE12There is a problem with the Gas Sensor or the associated wiring.mediumE13The oven did not pre-heat correctly.mediumE21The Thermal Sensor circuit reported open to the control board.medium
Call NowAvailable 24/7 — call or textBook Online