Want a regional phone & address? Pick your area.
Hotpoint·Dryerhigh severity
Hotpoint Dryer Error Code E8
Drive motor will not run
Common Causes
- 1Drive motor winding open
- 2Centrifugal start switch on the shaft failed
- 3Thermal overload latched open from a stall
Step-by-Step Troubleshooting
- 1
Roll the drum over by hand — a free spin throws suspicion on the motor, a bound drum means something has dropped between drum and bulkhead
- 2
With power off, comb the blower and drum edges for a fallen sock or coin seizing the works
- 3
Meter the motor windings and expect a low single-digit ohm reading across the run and start terminals
- 4
Inspect the centrifugal switch on the motor tail — a burnt switch blocks the start even with good windings
Pro Diagnostic Tip
This Hotpoint rides the GE dryer motor, which starts through a centrifugal switch on its shaft. A buzz on start that dies after a second or two usually fingers that switch rather than the motor windings, and the switch is the cheaper of the two to renew, so bench-test it first.
You Might Also Notice
- •No drum motion when you press start
- •A hum or buzz with the drum sitting still
- •A mid-cycle stall that will not restart
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$175–$375
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WE17X22217 drive motor assembly
Do You Have the Right Tools?
Gas leak detector ($130), thermal fuse tester ($95), belt tension gauge, and vent inspection camera ($180). Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
Gas dryers carry carbon monoxide and explosion risk. Even electric dryers involve 240V circuits that can deliver a fatal shock. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code E8 is a high-severity issue that can cause further damage to your dryer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Hotpoint error code E8 mean?
Hotpoint error code E8 indicates: Drive motor will not run. This is a high-severity issue affecting your dryer.
How do I fix Hotpoint error code E8?
Roll the drum over by hand — a free spin throws suspicion on the motor, a bound drum means something has dropped between drum and bulkhead Then, With power off, comb the blower and drum edges for a fallen sock or coin seizing the works Then, Meter the motor windings and expect a low single-digit ohm reading across the run and start terminals There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dryer has error E8?
Besides the error code on the display, common signs include: No drum motion when you press start; A hum or buzz with the drum sitting still; A mid-cycle stall that will not restart. If you notice any of these symptoms, check your dryer's display panel for error code E8.
How much does it cost to fix Hotpoint E8?
Repair costs for Hotpoint E8 typically range from $175 to $375 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related Hotpoint Dryer Error Codes
Call NowAvailable 24/7 — call or textBook Online