Want a regional phone & address? Pick your area.
Electrolux·Washer (Kenmore)low severity
Electrolux Washer (Kenmore) Error Code oL
Overloaded
Common Causes
- 1Too many items packed into the drum
- 2Heavy bedding or a load of towels
- 3Capacity exceeded for a single cycle
- 4Motor strain sensor or control board reading out of calibration
Step-by-Step Troubleshooting
- 1
Remove roughly a third of the load — clothes should fill the drum loosely, not packed tight
- 2
For bedding, wash one comforter at a time and add two or three towels for balance
- 3
Restart the cycle after reducing the load and confirm the drum turns freely by hand first
- 4
If oL returns on small, correctly sized loads, run the built-in diagnostic cycle to recalibrate the strain sensor before replacing any part
Pro Diagnostic Tip
oL is almost always a loading habit, not a fault — reduce the load and it clears for free. Only when it repeats on properly sized loads does the motor strain sensor or control board need recalibration or replacement, which is the small ceiling in the cost range.
You Might Also Notice
- •Motor strains audibly during agitation
- •Drum barely moves under load
- •Clothes still dirty or poorly rinsed after the cycle
- •oL appears even on modest loads
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$0–$130
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Motor strain sensorMain control board
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Diagnose the root cause, test affected components with calibrated meters, replace faulty parts with OEM replacements, and verify proper operation through a full test cycle.
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code oL disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Electrolux error code oL mean?
Electrolux error code oL indicates: Overloaded. This is a low-severity issue affecting your washer (kenmore).
How do I fix Electrolux error code oL?
Remove roughly a third of the load — clothes should fill the drum loosely, not packed tight Then, For bedding, wash one comforter at a time and add two or three towels for balance Then, Restart the cycle after reducing the load and confirm the drum turns freely by hand first There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer (kenmore) has error oL?
Besides the error code on the display, common signs include: Motor strains audibly during agitation; Drum barely moves under load; Clothes still dirty or poorly rinsed after the cycle. If you notice any of these symptoms, check your washer (kenmore)'s display panel for error code oL.
How much does it cost to fix Electrolux oL?
Repair costs for Electrolux oL typically range from $0 to $130 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related Electrolux Washer (Kenmore) Error Codes
Call NowAvailable 24/7 — call or textBook Online