Want a regional phone & address? Pick your area.
Beko·Dishwashermedium severity
Beko Dishwasher Error Code E01
Water intake fault — will not fill
Common Causes
- 1Supply tap closed
- 2Clogged inlet filter at the fill valve
- 3Fill (inlet) valve failed
- 4Low water pressure
Step-by-Step Troubleshooting
- 1
Confirm the supply tap under the sink is fully open and the fill hose is not kinked
- 2
Turn off the tap and clean the mesh screen where the fill hose meets the dishwasher valve
- 3
Listen at the start of a cycle for the inlet valve to buzz open — silence points to a failed valve
- 4
Unplug the dishwasher and test the inlet valve solenoid for continuity
- 5
Replace the fill valve if the screen is clear and the solenoid reads open
Pro Diagnostic Tip
A partly-closed shut-off after a plumbing repair is the most common E01 cause. Verify full tap flow into a jug before assuming the valve failed.
You Might Also Notice
- •Dishwasher stays dry at cycle start
- •Long delay before washing
- •No fill sound after the drain phase
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$90–$210
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water inlet (fill) valveInlet screen filter
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Open the supply tap fully and clean the inlet screen
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E01 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Beko error code E01 mean?
Beko error code E01 indicates: Water intake fault — will not fill. This is a medium-severity issue affecting your dishwasher.
How do I fix Beko error code E01?
Confirm the supply tap under the sink is fully open and the fill hose is not kinked Then, Turn off the tap and clean the mesh screen where the fill hose meets the dishwasher valve Then, Listen at the start of a cycle for the inlet valve to buzz open — silence points to a failed valve There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error E01?
Besides the error code on the display, common signs include: Dishwasher stays dry at cycle start; Long delay before washing; No fill sound after the drain phase. If you notice any of these symptoms, check your dishwasher's display panel for error code E01.
How much does it cost to fix Beko E01?
Repair costs for Beko E01 typically range from $90 to $210 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online