Dryer Repair in Mountain View
Professional dryer repair service in Mountain View, Santa Clara County
Same-Day Service
90-Day Warranty
Fixed or It's Free
Typical Cost: $100-$450
Book a Free Diagnostic Visit — Fully Online
Same-day dryer repair in Mountain View, Santa Clara County
Free DiagnosisSame-Day Service90-Day Warranty
How Much Does Dryer Repair Cost in Mountain View?
Dryer repair in Mountain View typically costs $100-$450, averaging $275. EasyBear provides same-day dryer repair in Mountain View with free diagnosis, 90-day warranty, and certified technicians.
- •Thermal fuse: $150-$200
- •Heating element (electric): $200-$300
- •Gas igniter / valve: $150-$250
- •Belt / drum rollers: $150-$250
- •Vent cleaning: $100-$150
Dryer Repair Cost in Mountain View
$235
Average Cost
$130 - $375
Typical Range
Prices include parts and labor. Free diagnostic when you proceed with repair.
What Are the Most Common Dryer Problems?
Not heating (electric or gas)
Takes too long to dry clothes
Won't start or turn on
Squeaking, thumping, or grinding noises
Drum not turning but motor runs
Burning or rubber smell
Shuts off mid-cycle
Exhaust vent restricted (d80/d90/d95)
Gas dryer not igniting
Overheating or too hot
Timer not advancing
Won't stop running
What Dryer Issues Do We Fix?
Dryer Not Heating
high priorityA dryer that tumbles but produces no heat leaves clothes damp and wastes your time. A burned-out heating element, a blown thermal fuse, or a faulty gas igniter are the most common causes. We restore proper heating so your laundry dries completely every cycle.
Burned-out heating elementBlown thermal fuseFaulty gas igniter
Cost: $150-$400Time: 45-90 minutes
Dryer Not Tumbling
high priorityWhen the dryer drum won't turn, your clothes sit in a heap and don't dry. A broken drive belt, worn drum rollers, or a failed motor are typical culprits. Our technicians replace the faulty parts and verify smooth, balanced drum rotation.
Broken drive beltWorn drum rollersFailed drive motor
Cost: $150-$350Time: 45-90 minutes
Dryer Taking Too Long to Dry
medium priorityExtended drying times waste energy and wear out your clothes. A clogged lint filter, a blocked vent duct, or a failing heating element significantly reduce drying efficiency. We clean, inspect, and repair the entire airflow and heating system.
Clogged lint filterBlocked vent ductFailing heating element
Cost: $100-$300Time: 30-75 minutes
Dryer Making Loud Noises
medium prioritySquealing, thumping, or grinding noises from your dryer usually indicate worn mechanical parts. Drum rollers, the idler pulley, and drum glides are common wear items. Ignoring these sounds can lead to complete breakdowns. We replace worn parts before they cause further damage.
Worn drum rollersDefective idler pulleyWorn drum glides
Cost: $125-$300Time: 45-90 minutes
Dryer Not Starting
high priorityWhen your dryer won't turn on at all, the issue could be a faulty door switch, a blown thermal fuse, or a defective start switch. These are safety-critical components. Our technicians safely diagnose and replace the failed part to restore operation.
Faulty door switchBlown thermal fuseDefective start switch
Cost: $100-$300Time: 30-60 minutes
Dryer Overheating
high priorityAn overheating dryer is a serious fire hazard. Restricted airflow from lint buildup, a failed cycling thermostat, or a defective high-limit thermostat can all cause excessive heat. Immediate professional repair is critical for your family's safety.
Lint buildup in ventFailed cycling thermostatDefective high-limit thermostat
Cost: $150-$350Time: 45-90 minutes
Dryer Drum Stuck or Seized
high priorityA seized dryer drum prevents any drying and can damage the motor if forced. Worn drum bearings, a broken belt, or an obstruction between the drum and housing are common causes. We free the drum and replace any worn components.
Worn drum bearingsBroken drive beltObstruction between drum and housing
Cost: $150-$350Time: 60-120 minutes
Dryer Leaving Clothes Wrinkled
low priorityExcessive wrinkling after drying can result from overloading, a malfunctioning moisture sensor, or an incorrect heat setting. While sometimes a usage issue, persistent wrinkling may indicate a failing sensor or timer. We diagnose the cause and optimize your dryer's performance.
Malfunctioning moisture sensorFaulty timerOverloaded drum
Cost: $100-$250Time: 30-60 minutes
Get Your Dryer Fixed Today
Free diagnosis when you book online
Free DiagnosisSame-Day Service90-Day Warranty
Why Choose EasyBear in Mountain View?
Same-Day Service
Most repairs completed same day
90-Day Warranty
Comprehensive coverage
No Diagnostic Fee
Free inspection
Book a Free Diagnostic Visit — Fully Online
Free DiagnosisSame-Day Service90-Day Warranty
Serving Mountain View:
940409404194043
About Dryer Repair in Mountain View
Dryer repair in Mountain View navigates the practical constraints of the city's mid-century ranch homes and the growing demand for ventless solutions in new multi-family construction. The ranch homes in Waverly Park, Sylvan Park, and Rex Manor feature dryer venting routed through walls or ceilings to exterior termination points — installations designed when dryers were lower-capacity and vent runs were shorter. Over decades, these original vent configurations have accumulated lint at joints and elbows, and the galvanized or flexible duct materials used in the 1950s and 1960s trap lint far more aggressively than modern rigid aluminum ductwork. A Mountain View technician diagnosing a dryer that runs hot but fails to dry clothes efficiently will almost always find the vent run as a contributing factor.
Gas dryers are standard in Mountain View's older neighborhoods, connected to PG&E gas lines installed during original construction. The gas igniter — a flat silicon carbide element that must glow hot enough to trigger the gas safety valve — is the most commonly replaced gas dryer component in Mountain View. These igniters become brittle after several years of thermal cycling, and when they crack or weaken, the dryer tumbles without heat. Gas valve solenoids are the second most common failure, with the solenoid coils developing intermittent failures that cause the dryer to heat initially but lose heat partway through the cycle as the coils overheat and lose their magnetic holding force.
Mountain View's new apartment and condo developments increasingly specify ventless heat pump or condensation dryers that eliminate the need for exterior vent penetrations through the building envelope. These ventless units require no ductwork but introduce condensation collection systems and, in the case of heat pump dryers, sealed refrigerant circuits that demand specialized repair knowledge. The shift from vented to ventless dryer technology in Mountain View's housing market is creating demand for technicians who can service both categories competently.
Frequently Asked Questions
Dryer repair costs range from $100-$450, averaging $275 in the Bay Area. Common repairs include thermal fuse ($150-$200), heating element for electric dryers ($200-$300), igniter for gas dryers ($150-$250), and belt replacement ($150-$250).
For electric dryers, common causes are blown thermal fuse, bad heating element, or faulty thermostat. For gas dryers, it's usually a weak or failed igniter or faulty gas valve. Check the circuit breaker first (electric) or gas supply valve (gas), then call a professional for internal components.
Dryers average 12 years, with a range of 10-13 years. Gas dryers tend to last slightly longer than electric. Regular vent cleaning and not overloading extends dryer lifespan.
The most common cause is a clogged dryer vent or lint trap. Clean the lint trap after every load and have your vent system professionally cleaned annually. Other causes include weak heating element/igniter or moisture sensor issues.
If you smell gas from a gas dryer, shut off the gas valve immediately and call a professional - this is an emergency. Otherwise, a dryer that won't heat is inconvenient but not dangerous. However, a clogged vent CAN be dangerous (fire risk), so address it promptly.
Use the 50% rule: if repair costs exceed 50% of a new dryer and the unit is over 8 years old, consider replacing. A new dryer costs $400-$1,200. For repairs under $300 on a dryer less than 10 years old, repair almost always makes more sense.
Dryer repairs typically cost between $100 and $450, with the average around $275. Common repairs like replacing a heating element cost $150–$300, while drum roller or motor replacement can run $200–$450. Gas dryer repairs tend to cost $50–$100 more than electric models due to additional components.
For electric dryers, the most common causes are a burned-out heating element, a faulty thermal fuse, or a broken thermostat. For gas dryers, check the gas valve solenoid, igniter, or flame sensor. A tripped circuit breaker (electric dryers need both legs of a 240V circuit) is also common. Heating repairs cost $150–$350.
The #1 cause is a clogged lint trap or vent duct, which restricts airflow and can increase drying time by 50–100%. Clean the lint trap after every load and have the vent duct professionally cleaned annually. Other causes include a failing heating element, a worn drum seal, or an overloaded drum.
Professional dryer vent cleaning should be done at least once a year, or more frequently if you do more than 5 loads per week. A clogged dryer vent is a leading cause of house fires — approximately 2,900 dryer fires occur annually in the US. Vent cleaning costs $100–$170 and improves efficiency by up to 30%.
Squeaking usually indicates worn drum support rollers, a frayed drum belt, or dry drum bearing glides. Thumping is often caused by flat spots on the drum rollers from sitting idle. These parts wear out after 5–8 years of regular use. Drum roller and belt replacement costs $150–$300 including parts and labor.
Most dryer repairs take 45 minutes to 1.5 hours. Heating element and thermostat replacements take about 1 hour. Belt and drum roller repairs take 1–1.5 hours since the drum needs to be removed. About 85% of dryer repairs are completed in a single visit.
A dryer with a broken heating element will tumble but not produce heat — it won't dry your clothes and wastes electricity. It's safe to run but pointless. However, if you smell burning or see scorch marks, stop using the dryer immediately and call for repair, as this could indicate a wiring issue or lint ignition risk.
Dryers typically last 10–14 years. For a 10-year-old dryer, repairs under $250 are usually worthwhile. If the motor or control board needs replacement ($350+), consider a new dryer. Newer dryers offer better energy efficiency, moisture sensors, and steam features that may save money over time.
This is usually caused by an overheating thermal fuse, which trips when the dryer gets too hot due to restricted airflow. The most common cause is a clogged vent duct. Check and clean the vent first, then the thermal fuse may need replacement ($80–$150). Repeated tripping indicates a deeper airflow or cycling thermostat issue.
Yes, we repair both gas and electric dryers. Gas dryer repairs cost about $50–$100 more on average due to additional components like gas valve coils, igniters, and flame sensors. Gas-specific repairs like replacing valve solenoids cost $150–$300. Always hire a professional for gas dryer repairs — gas leaks are dangerous.
Wrinkled clothes often result from overloading the dryer, leaving clothes sitting after the cycle ends, or over-drying. Use the moisture sensor or auto-dry setting instead of timed drying. Remove clothes promptly when the cycle ends. If wrinkles persist with proper use, the moisture sensor may need calibration or replacement ($100–$200).
A drum that won't turn is usually caused by a broken drive belt (the most common cause), a seized drum roller, or a failed motor. You may hear the motor humming without the drum spinning, which confirms a belt issue. Belt replacement is one of the more affordable dryer repairs at $100–$200 including labor.
Clean the lint trap after every load, have the vent duct professionally cleaned annually, and ensure the vent exhausts outdoors (not into the attic or crawlspace). Don't dry items stained with flammable substances. Use rigid metal vent ducts instead of flexible foil or plastic. Keep the area around the dryer free of combustible materials.
Dryer error codes indicate specific component failures such as thermistor errors, heating element faults, door switch issues, or motor problems. Common Samsung codes include HE (heating error), dC (door open), and tS (temperature sensor). Note the exact code and contact us — we can often pre-diagnose the issue before scheduling a visit.
A burning smell is a serious safety concern. Turn off and unplug the dryer immediately. Common causes include lint buildup near the heating element, a worn belt producing rubber smell, or a failing motor. Don't use the dryer until it's been inspected. Lint-related burning smell repairs typically cost $100–$200 including thorough cleaning.
Black marks or streaks on clothes are usually caused by worn drum felt seals, damaged drum glides, or a foreign object stuck between the drum and the housing. Grease from worn bearings can also transfer to clothes. Inspect the front and rear drum seals for wear. Drum seal and glide replacement costs $100–$250 and prevents further clothing damage.
Need Dryer Repair in Mountain View?
Book your same-day repair service now
Free DiagnosisSame-Day Service90-Day Warranty
Dryer repair in the San Francisco and Bay Area— local context
Climate impact: Coastal salt air corrodes outdoor dryer vent hoods and lint-duct fasteners across 94121, 94122, 94127 and 94116 faster than inland SF — we rebuild the vent path during service when needed.
Common local issue: Blocked or crushed vent run (especially in Victorian attics) masquerading as a heating-element failure. Always check vent path before replacing heating assemblies.
Parts we carry: Stainless-steel outdoor vent hoods stocked for coastal SF / Pacifica / Daly City.