Want a regional phone & address? Pick your area.
Kenmore·Ovenhigh severity
Kenmore Oven Error Code F2
Runaway oven over-temperature
Common Causes
- 1RTD probe shorted low
- 2Bake or broil relay welded closed
- 3Element driven with no thermostatic cutback
F2 is a fire safety code. Do not use the oven until repaired. Keep breaker off until diagnosed.
Step-by-Step Troubleshooting
- 1
Cancel the bake, crack the door to vent the heat, and drop the breaker without delay
- 2
Once the cavity cools, ohm the RTD probe and expect about eleven hundred ohms at room temperature
- 3
A probe that reads normal points the finger at a welded bake or broil relay on the control
- 4
Renew a shorted probe, or replace the control when a stuck relay is holding the element on
Pro Diagnostic Tip
On this Whirlpool-platform 790-series Kenmore an over-temperature reading is a safety fault — kill power at the breaker the moment the oven runs away hot. After it cools, ohm the RTD sensor at room temperature; if the sensor reads normal, a welded bake or broil relay on the control is holding the element on and the board is replaced.
You Might Also Notice
- •The oven climbing well past the set temperature
- •Food burning despite correct settings
- •Smoke rolling out during an ordinary bake
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$100–$350
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W10181986 oven temperature sensorW10842899 electronic control board
Do You Have the Right Tools?
Combustion analyzer ($300), igniter tester ($120), temperature calibrator ($150), and gas pressure manometer. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
Gas ovens involve live gas lines — a loose connection creates explosion and carbon monoxide risk. Electric ovens run on 240V circuits. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F2 is a high-severity issue that can cause further damage to your oven if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Kenmore error code F2 mean?
Kenmore error code F2 indicates: Runaway oven over-temperature. This is a high-severity issue affecting your oven.
How do I fix Kenmore error code F2?
Cancel the bake, crack the door to vent the heat, and drop the breaker without delay Then, Once the cavity cools, ohm the RTD probe and expect about eleven hundred ohms at room temperature Then, A probe that reads normal points the finger at a welded bake or broil relay on the control There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my oven has error F2?
Besides the error code on the display, common signs include: The oven climbing well past the set temperature; Food burning despite correct settings; Smoke rolling out during an ordinary bake. If you notice any of these symptoms, check your oven's display panel for error code F2.
How much does it cost to fix Kenmore F2?
Repair costs for Kenmore F2 typically range from $100 to $350 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online