Want a regional phone & address? Pick your area.
Hisense·Dishwashermedium severity
Hisense Dishwasher Error Code E1
Water intake fault — will not fill
Common Causes
- 1Supply tap closed
- 2Clogged inlet filter
- 3Fill valve failed
- 4Low water pressure
Step-by-Step Troubleshooting
- 1
Confirm the under-sink supply valve is fully open and the fill hose is not kinked
- 2
Shut the tap and clean the inlet screen where the hose threads onto the dishwasher valve
- 3
Start a cycle and listen for the fill valve to buzz; silence points to a dead solenoid
- 4
Unplug the dishwasher and test the inlet valve coil for continuity
- 5
Replace the fill valve if the screen is clear and the coil reads open
Pro Diagnostic Tip
A supply valve left half-closed after a disposer or faucet job is the top E1 cause on a recently-serviced kitchen — check full tap flow before condemning the valve.
You Might Also Notice
- •Dishwasher stays dry at start
- •Long delay before wash begins
- •No fill sound after draining
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$85–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water inlet (fill) valveInlet screen filter
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Open the supply tap fully and clean the fill screen
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Hisense error code E1 mean?
Hisense error code E1 indicates: Water intake fault — will not fill. This is a medium-severity issue affecting your dishwasher.
How do I fix Hisense error code E1?
Confirm the under-sink supply valve is fully open and the fill hose is not kinked Then, Shut the tap and clean the inlet screen where the hose threads onto the dishwasher valve Then, Start a cycle and listen for the fill valve to buzz; silence points to a dead solenoid There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error E1?
Besides the error code on the display, common signs include: Dishwasher stays dry at start; Long delay before wash begins; No fill sound after draining. If you notice any of these symptoms, check your dishwasher's display panel for error code E1.
How much does it cost to fix Hisense E1?
Repair costs for Hisense E1 typically range from $85 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online