Want a regional phone & address? Pick your area.
Haier·Dishwashermedium severity
Haier Dishwasher Error Code E5
Temperature sensor (NTC) out of range
Common Causes
- 1Open or shorted NTC sensor
- 2Sensor connector loose or corroded
- 3Sensor drifted out of tolerance
- 4Harness pinched near the sump
Step-by-Step Troubleshooting
- 1
Unplug the dishwasher and locate the NTC sensor threaded into the Haier sump or wash-water path
- 2
Measure its resistance cold and compare against the rated value, replacing it when the reading is open, shorted, or far off
- 3
Reseat the sensor connector and check for corrosion that raises resistance and pushes the reading out of range
- 4
Inspect the harness where it passes the sump for a pinch or melt point that alters the signal
- 5
Clear E5 after the sensor tests within range, then run a hot cycle to confirm the temperature climbs normally
Pro Diagnostic Tip
Haier pairs E5 (sensor out of range) with E3 (no heat) on the same NTC, so when both appear together suspect the sensor connector first, since one loose plug throws the pair at once.
You Might Also Notice
- •Cycle aborts early
- •Water runs too hot or stays cold
- •Inconsistent cycle times
- •Sanitising phase skipped
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$90–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
NTC temperature sensorSensor wiring connector
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E5 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Haier error code E5 mean?
Haier error code E5 indicates: Temperature sensor (NTC) out of range. This is a medium-severity issue affecting your dishwasher.
How do I fix Haier error code E5?
Unplug the dishwasher and locate the NTC sensor threaded into the Haier sump or wash-water path Then, Measure its resistance cold and compare against the rated value, replacing it when the reading is open, shorted, or far off Then, Reseat the sensor connector and check for corrosion that raises resistance and pushes the reading out of range There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error E5?
Besides the error code on the display, common signs include: Cycle aborts early; Water runs too hot or stays cold; Inconsistent cycle times. If you notice any of these symptoms, check your dishwasher's display panel for error code E5.
How much does it cost to fix Haier E5?
Repair costs for Haier E5 typically range from $90 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online